The composite material flywheel rotor of a flywheel energy storage system (FESS) has a low natural frequency. When the system suffers from noise interference, the magnetic bearing generates a force with the same frequency as the natural frequency and causes vibration to occur. Thus, it is necessary to suppress the natural vibration of the magnetic suspended (MS) FESS. The LMS adaptive notch filter is generally adopted for vibration suppression. The vibration suppression performance of the system is different when the insertion position of the notch filter is different. This paper analyzes the influence of the notch filter in different insertion positions of the control system. Through the transfer function from noise to magnetic bearing force, theoretical analysis of the influence of different positions of the notch filter is performed. Corresponding experiments are performed in a 500 kW MS FESS prototype. The theoretical analysis is verified experimentally.
To realize the hyperstatic performance index of a magnetically suspended flywheel and simultaneously suppress the vibration force caused by mass imbalance and sensor runout, a compound control method based on a repetitive controller and displacement force compensation of the synchronous force is proposed. First, the mechanism of different interference vibration forces is analyzed by establishing a model of the magnetically suspended flywheel. The analysis shows that the x–y direction is symmetric, and the flywheel structure has symmetry. Second, considering the symmetry of the x- and y-directions, the x-direction is taken as an example for analysis, the parameter design and stability analysis are carried out, and the range of parameters of the compound repetitive control method is obtained. Finally, a flywheel with different speeds is simulated. It was found that the vibration force of each frequency can be suppressed by the compound control method, and the inhibition rate of the vibration force can reach as much as 95%. The results show that the unbalanced vibration and vibration force caused by the sensor runout can be effectively suppressed by using the compound repetitive control method.
Flywheel energy storage systems exhibit superior performance in electric vehicle regenerative braking, railway traction power supply, and grid frequency regulation due to their high instantaneous power and fast dynamic response. However, systems supported by conventional mechanical bearings face severe radial structural coupling; unbalanced excitation and gyroscopic effects drastically amplify vibrations during critical speed traversal, undermining operational reliability and engineering scalability. To tackle this challenge, this paper proposes a full-speed vibration suppression scheme for active–passive supported flywheel energy storage systems integrated with a damping ring, combined with an inverse system decoupling controller to eliminate structural coupling, unbalance-induced vibration, and gyroscopic effects. A dynamic model of the integrated system is established using Lagrange’s equations, and four-degree of freedom decoupling expressions are derived to achieve complete radial decoupling. A speed-stage-based control strategy is further developed for full-speed adaptation. Comprehensive simulations validate the scheme’s decoupling performance, vibration suppression efficacy, and robustness. Results demonstrate that the proposed controller achieves full radial decoupling, reducing the average steady-state tracking error by 99.86%. The segmented control enables stable operation across 100–20,000 rpm and cuts critical speed resonance peaks by 81.23%. Compared with pure mechanical and magnetic bearing systems, the integrated active–passive support reduces resonance peaks by 94.72% and 42.25%, respectively. Under current perturbation and parameter variation, the scheme reduces the average steady-state error by 75.89% relative to the coupled system, confirming its strong engineering applicability.
Magnetic bearing flywheels, characterized by frictionless operation and long service life, are increasingly recognized as promising actuators for spacecraft attitude control. Understanding their dynamic behavior under moving-base conditions is therefore essential. In this study, the Lagrange method is employed to derive the dynamic equations of a magnetic-bearing flywheel subject to base motion. By incorporating the dynamics of electromagnetic bearings, a unified electromechanical-dynamic control model is established. Simulations are conducted to examine the system’s response during rapid maneuvers, with a focus on the effects of base moment of inertia, rotor speed, and maneuver angular rate on flywheel performance. Based on the analysis, a feedforward compensation strategy utilizing the angular acceleration of the moving base is proposed to suppress the influence of base motion. Simulation results validate the effectiveness of the proposed method, offering technical support for the future application of magnetically levitated flywheels in ultra-stable, fast-maneuvering satellites.