In this paper, a complementary split-ring resonator (CSRR)-loaded patch is proposed as a microfluidic ethanol chemical sensor. The primary objective of this chemical sensor is to detect ethanol’s concentration. First, two tightly coupled concentric CSRRs loaded on a patch are realized on a Rogers RT/Duroid 5870 substrate, and then a microfluidic channel engraved on polydimethylsiloxane (PDMS) is integrated for ethanol chemical sensor applications. The resonant frequency of the structure before loading the microfluidic channel is 4.72 GHz. After loading the microfluidic channel, the 550 MHz shift in the resonant frequency is ascribed to the dielectric perturbation phenomenon when the ethanol concentration is varied from 0% to 100%. In order to assess the sensitivity range of our proposed sensor, various concentrations of ethanol are tested and analyzed. Our proposed sensor exhibits repeatability and successfully detects 10% ethanol as verified by the measurement set-up. It has created headway to a miniaturized, non-contact, low-cost, reliable, reusable, and easily fabricated design using extremely small liquid volumes.

Metamaterial elements/arrays exhibit a sensitive response to fluids yet with a small footprint, therefore, they have been an attractive choice to realize various sensing devices when integrated with microfluidic technology. Micro-channels made from inexpensive biocompatible materials avoid any contamination from environment and require only microliter–nanoliter sample for sensing. Simple design, easy fabrication process, light weight prototype, and instant measurements are advantages as compared to conventional (optical, electrochemical and biological) sensing systems. Inkjet-printed flexible sensors find their utilization in rapidly growing wearable electronics and health-monitoring flexible devices. Adequate sensitivity and repeatability of these low profile microfluidic sensors make them a potential candidate for point-of-care testing which novice patients can use reliably. Aside from degraded sensitivity and lack of selectivity in all practical microwave chemical sensors, they require an instrument, such as vector network analyzer for measurements and not readily available as a self-sustained portable sensor. This review article presents state-of-the-art metamaterial inspired microfluidic bio/chemical sensors (passive devices ranging from gigahertz to terahertz range) with an emphasis on metamaterial sensing circuit and microfluidic detection. We also highlight challenges and strategies to cope these issues which set future directions.

Owing to the rapid growth in wireless data traffic, millimeter-wave (mm-wave) communications have shown tremendous promise and are considered an attractive technique in fifth-generation (5G) wireless communication systems. However, to design robust communication systems, it is important to understand the channel dynamics with respect to space and time at these frequencies. Millimeter-wave signals are highly susceptible to blocking, and they have communication limitations owing to their poor signal attenuation compared with microwave signals. Therefore, by employing highly directional antennas, co-channel interference to or from other systems can be alleviated using line-of-sight (LOS) propagation. Because of the ability to shape, switch, or scan the propagating beam, phased arrays play an important role in advanced wireless communication systems. Beam-switching, beam-scanning, and multibeam arrays can be realized at mm-wave frequencies using analog or digital system architectures. This review article presents state-of-the-art phased arrays for mm-wave mobile terminals (MSs) and base stations (BSs), with an emphasis on beamforming arrays. We also discuss challenges and strategies used to address unfavorable path loss and blockage issues related to mm-wave applications, which sets future directions.

In this paper, we propose an angle- and polarization-insensitive broadband metamaterial absorber with a resistive fan-shaped resonator. First, the symmetric fan-shaped resonator is designed, and four lumped resistors are loaded in the gap between each fan-shaped circular sector on the top layer to increase the bandwidth. Based on the circuit parameters, the periodic structure of the fan-shaped resonator is designed using full-wave analysis. The proposed absorber is fabricated using a printed circuit board process in a single layer. The experimental results indicate that an absorptivity value greater than 96% was achieved in the frequency range of 7–12.8 GHz for all polarization angles at normal incidence. Under oblique incidence, the measured absorptivity was greater than 90% in the range of 7–12.1 GHz when the incident angle varied from 0° to 45° in the transverse electric mode. In the transverse magnetic mode, the measured absorptivity was greater than 90% between 7.1 and 9.3 GHz when the incident angle varied from 0° to 45°.

In this paper, a broadband metamaterial (MM) absorber is presented for X-band applications. A novel eight-resistive-arm (ERA) cell is proposed as an MM unit cell to achieve both broadband absorption and wide incidence angles. The proposed ERA cell is designed using equivalent circuit model and full-wave analysis in order to achieve an absorption ratio higher than 90% in the range of 8.2–13.4 GHz. The experimental results indicate that the absorptivity was greater than 90% in the range of 8–13 GHz for all polarization angles under normal incidence. Under oblique incidence, the measured absorptivity was greater than 90% in the range of 8.2–12.2 GHz up to 60° and in the range of 9.2–12 GHz up to 65° in the transverse electric (TE) mode. In the transverse magnetic (TM) mode, the measured absorptivity was higher than 90% in the range of 9.5–12.4 GHz when the incidence angle was varied from 0° to 60° and remaining a 90% absorption bandwidth in the range of 10–12 GHz up to 65°. Compared to other broadband MM absorbers, the proposed MM absorber exhibited the widest incidence angles in both TE and TM modes.