This paper focuses on invetigating the relationship between the contact features of the tyres and the tyre wear in a quantitative sense as a function of the tyre structure and the manoeuvre parameters by utilizing a modified theoretical tyre wear model. The modified tyre wear model was developed by combining a modified ring model for the tyres and a modified brush model and was validated. The model parameters were also identified by physical experiments. Moreover, the contact features were characterized as the contact length, the asymmetry factor and the rolling resistance shift in order to investigate the influence of the contact features on the tyre wear. The amount of wear versus the three key variables of the contact features with variations in the tyre parameters was plotted and analysed. The results show that the maximum normal contact pressure does not play the most important role in the tyre wear. An increase in the damping coefficient can lead to an increase in the tyre wear, whereas increases in the effective elastic constant, the effective bending density and the effective bending stiffness result in a decrease in wear. The three key variables of the contact features increase with increasing vertical load, increasing rolling velocity and increasing damping coefficient and with decreasing inflation pressure and decreasing effective bending stiffness. The tyre wear follows the same trend when the three key variables increase or decrease synchronously. This analysis provides a quantitative indication of the relationship between the contact features and the tyre wear in order to obtain guidelines for tyre manufacturers on how to achieve less tyre wear.
An important component of the U.S. effort to achieve thermonuclear ignition in 2010 on the National Ignition Facility is the development of high quality 2 mm diameter spherical capsules to function as the ablator and contain the cryogenic DT fuel. Three ignition capsule designs have been developed, and detailed fabrication specifications for each design have been established and placed under change control. A research program with activities coordinated mainly between Lawrence Livermore, General Atomics and Los Alamos is underway to demonstrate fabrication of capsules meeting specifications. The point design for ignition campaigns beginning in 2010 is a Cu-doped Be capsule that has a radial gradient in Cu dopant level in the capsule wall. This capsule is being produced by sputter deposition of Be and Cu onto either a hollow glow discharge polymer (GDP) spherical mandrel or a solid spherical mandrel, followed by removal of the mandrel and polishing of the capsule. A key goal in the U.S. is to demonstrate fabrication of this capsule by the end of 2006. Two other ignition capsule designs are also being developed as contingencies to the point design. One contingency design is a GDP capsule that has a radial Ge dopant level in its wall. This capsule is produced by co-deposition of Ge and GDP onto a PAMS mandrel followed by thermal removal of the mandrel. The second contingency design is a uniform Cu-doped Be capsule that is fabricated from high purity fine grain Be0.3at.%Cu alloy using a precision machining route followed by polishing. Ignition targets to be fielded in 2010 will be filled with DT fuel through a small fill hole. Laser drilling capability has been developed and used to drill approximately 5 μm diameter holes through capsule walls for DT filling. Characterization methods necessary for characterizing capsules are being developed.
To investigate the tribological performance of a copper alloy engine bearing under oil lubrication, seawater corrosion and dry sliding wear, three different PI/PAI/EP coatings consisting of 1.5 wt% Ce2O3, 2 wt% Ce2O3, 2.5 wt% Ce2O3 were designed, respectively. These designed coatings were prepared on the surface of CuPb22Sn2.5 copper alloy using a liquid spraying process. The tribological properties of these coatings under different working conditions were tested. The results show that the hardness of the coating decreases gradually with the addition of Ce2O3, and the agglomeration of Ce2O3 is the main reason for the decrease of hardness. The wear amount of the coating increases first and then decreases with the increase of Ce2O3 content under dry sliding wear. The wear mechanism is abrasive wear under the condition of seawater. The wear resistance of the coating decreases with the increase of Ce2O3 content. The wear resistance of the coating with 1.5 wt% Ce2O3 is the best under-seawater corrosion. Although Ce2O3 has corrosion resistance, the coating of 2.5 wt% Ce2O3 has the worst wear resistance under seawater conditions due to severe wear caused by agglomeration. Under oil lubrication conditions, the frictional coefficient of the coating is stable. The lubricating oil film has a good lubrication and protection effect.
31 October 2014 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
A theoretical tyre model was developed analytically using the proposed middle plane for predicting the three-dimensional global tyre wear qualitatively and quantitatively as a function of the road roughness and the dynamic characteristics of the vehicle. Diagrams of the tyre wear pattern across the tyre width and along the tyre circumference were drawn for different road roughnesses, camber angles and vehicle dynamic characteristics. The numerical results show how the three-dimensional tyre wear pattern varied when these factors changed. Numerical calculations also reveal that a unique wear pattern may be caused by the system’s inherent dynamic features, e.g. the modal shape. In addition, a sensitivity analysis shows that the slip ratio, the longitudinal stiffness, the tyre width, the velocity and the vertical force have the greatest effects on the frictional dissipation energy, in that order. With the established wear model, good tyre wear distribution predictions can be given qualitatively and quantitatively for the rolling surface of the tyre. Moreover, guidelines for obtaining less tyre wear are provided for tyre and car manufacturers.
Experiments at the National Ignition Facility (NIF) show that the implosion shape of inertial confinement fusion ablators is a key factor limiting performance. To achieve more predictable, shape tunable implosions, we have designed and fielded a large 4.2 case-to-capsule ratio target at the NIF using 6.72 mm diameter Au hohlraums and 1.6 mm diameter Cu-doped Be capsules. Simulations show that at these dimensions during a 10 ns 3-shock laser pulse reaching 275 eV hohlraum temperatures, the plasma flow from the hohlraum wall and ablator is not significant enough to impede beam propagation. Experiments measuring the shock symmetry and in-flight shell symmetry closely matched the simulations. Most notably, in two experiments, we demonstrated symmetry control from negative to positive Legendre P2 space by varying the inner to total laser power cone fraction by 5% below and above the predicted symmetric value. Some discrepancies found in 1st shock arrival times that could affect agreement in late time implosion symmetry suggest hohlraum and capsule modeling uncertainties do remain, but this target design reduces sensitivities to them.