Shuxin Li

Prof. Shuxin Li


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 June 2021 in Fatigue & Fracture of Engineering Materials & Structures
Verified
Journal Article
Closed access
PDF file
HZHuan‐Jie Zhang
Huan‐Jie Zhang
FYFeng Yu
Feng Yu
SLShuxin Li
Shuxin Li
EHEn‐Guang He
En‐Guang He

17 March 2023 in Polymers
Verified
Journal Article
Open access
PDF file
SYShijie Yu
Shijie Yu
JCJun Cao
Jun Cao
SLShuxin Li
Shuxin Li
HHHaibo Huang
Haibo Huang
XLXiaojie Li
Xiaojie Li
To investigate the tribological performance of a copper alloy engine bearing under oil lubrication, seawater corrosion and dry sliding wear, three different PI/PAI/EP coatings consisting of 1.5 wt% Ce2O3, 2 wt% Ce2O3, 2.5 wt% Ce2O3 were designed, respectively. These designed coatings were prepared on the surface of CuPb22Sn2.5 copper alloy using a liquid spraying process. The tribological properties of these coatings under different working conditions were tested. The results show that the hardness of the coating decreases gradually with the addition of Ce2O3, and the agglomeration of Ce2O3 is the main reason for the decrease of hardness. The wear amount of the coating increases first and then decreases with the increase of Ce2O3 content under dry sliding wear. The wear mechanism is abrasive wear under the condition of seawater. The wear resistance of the coating decreases with the increase of Ce2O3 content. The wear resistance of the coating with 1.5 wt% Ce2O3 is the best under-seawater corrosion. Although Ce2O3 has corrosion resistance, the coating of 2.5 wt% Ce2O3 has the worst wear resistance under seawater conditions due to severe wear caused by agglomeration. Under oil lubrication conditions, the frictional coefficient of the coating is stable. The lubricating oil film has a good lubrication and protection effect.

6 April 2022 in Materials
Verified
Journal Article
Open access
PDF file
SXSheng Xu
Sheng Xu
HXHaijie Xu
Haijie Xu
Xuedao ShuXuedao Shu
Xuedao Shu
SLShuxin Li
Shuxin Li
ZSZhongliang Shen
Zhongliang Shen
Warm compression tests were carried out on low carbon and low alloy steel at temperatures of 600–850 °C and stain rates of 0.01–10 s−1. The evolution of microstructure and texture was studied using a scanning electron microscope and electron backscattered diffraction. The results indicated that cementite spheroidization occurred and greatly reduced at 750 °C due to a phase transformation. Dynamic recrystallization led to a transition from {112} texture to {111} texture. Below 800 °C, the intensity and variation of texture with deformation temperature is more significant than that above 800 °C. The contents of the {111} texture and {111} texture were equivalent above 800 °C, resulting in the better uniformity of γ-fiber texture. Nucleation of //ND-oriented grains increased, leading to the strengthening of //ND texture. Microstructure analysis revealed that the uniform and refined grains can be obtained after deformation at 800 °C and 850 °C. The texture variation reflected the fact that 800 °C was the critical value for temperature sensitivity of warm deformation. At a large strain rate, the lowest dislocation density appeared after deformation at 800 °C. Therefore, 800 °C is a suitable temperature for the warm forming application, where the investigated material is easy to deform and evolves into a uniform and refined microstructure.

29 November 2020 in Metals
Verified
Journal Article
Open access
PDF file
SXSheng Xu
Sheng Xu
Xuedao ShuXuedao Shu
Xuedao Shu
SLShuxin Li
Shuxin Li
JCJi Chen
Ji Chen
The warm deformation behavior of 20CrMoA steel at the temperature of 873–1123 K and the strain rate of 0.01−10 s−1 was investigated to obtain its processing property and optimum processing parameters. The true stress-true strain curves showed that flow stress reaches the peak rapidly, followed by slow decrease till reaching a steady state. This suggests a flow softening of dynamic recovery. The stress dropped with increasing deformation temperature and decreasing strain rate. The reduction became more distinct at lower temperature and higher strain rate due to flow softening caused by deformation heat. In the temperature range of 873–973 K, the deformation of 20CrMoA steel was more sensitive to temperature, and the average decline rate of steady stress was 6.9 times larger than that in the temperature range of 1023–1123 K. After modifying the stress curves, a constitutive model was developed for different deformation temperature ranges based on modified curves. The model was in good agreement with the experimental results.

10 May 2024 in Wear
Verified
Journal Article
Closed access
JCJinhua Chen
Jinhua Chen
YWYibo Wang
Yibo Wang
SLShuxin Li
Shuxin Li
XHXinqi Han
Xinqi Han
SLSiyuan Lu
Siyuan Lu
YJYongsheng Jin
Yongsheng Jin

1 April 2026 in Friction
Verified
Journal Article
Open access
PDF file
GJGanghui Jiang
Ganghui Jiang
SLShuxin Li
Shuxin Li
JPJibin Pu
Jibin Pu
LHLicheng Hua
Licheng Hua
SLSiyuan Lu
Siyuan Lu
The complex electrical environments inherent in electric vehicles often lead to premature failures of bearings. A comprehensive understanding of material behavior under current-carrying conditions is therefore essential. In this study, a current-carrying pin-on-disk tribometer was used to investigate the tribological response and microstructural degradation of bearing steel subjected to electric current. The results show that electric current significantly intensifies adhesive, oxidative, and abrasive wear, leading to increased coefficient of friction (COF) and wear volume. After 120 min of sliding, the average COF increases from 0.058 at 0 A to 0.066 at 1.5 A and 0.072 at 6 A, while the corresponding wear volumes at 1.5 A and 6 A are approximately 1.5 and 2 times that at 0 A, respectively. This deterioration is attributed to the combined effects of electro-thermal and athermal mechanisms. Specifically, arc discharge in conjunction with frictional heating rapidly raises the surface temperature, inducing subsurface tempering and dynamic recrystallization. These thermally activated processes lead to microstructural softening, which in turn facilitates severe plastic deformation. Meanwhile, athermal effects accelerate dislocation motion and rearrangement, further affecting the material's mechanical properties.