Auto-oscillations may occur in moving vehicles in the area where the tire interacts with the support base. The parameters of such oscillations depend on the sliding velocity in the contact patch. As they negatively affect the processes occurring in the electric drive and the mechanical transmission, reducing their energy efficiency, such processes can cause failures in various elements. This paper aims to conduct a theoretical study into the peculiarities of oscillatory processes in the nonlinear system and an experimental study of the auto-oscillation modes of an individual traction drive. It presents the theoretical basis used to analyze the peculiarities of oscillation processes, including their onset and course, the results of simulation mathematical modeling and the experimental studies into the oscillation phenomena in the movement of the vehicle towards the supporting base. The practical value of this study lies in the possibility to use the results in the development of algorithms for the exclusion of auto-oscillation phenomena in the development of vehicle control systems, as well as to use the auto-oscillation processes onset and course analysis methodology to design the electric drive of the driving wheels.
Введение. Электрифицированные транспортные средства (ЭТС) в последние годы активно развиваются в мегаполисах Российской Федерации. В связи со специфичными климатическими условиями нашей страны производители ЭТС сталкиваются со сложностями при проектировании и при создании имитационных моделей, а также при выборе расчётных случаев для них. Основным критерием безопасности и степени деградации (SoH) тяговой аккумуляторной батареи (ТАБ) является диапазон температур, при которых она эксплуатируется. Цель исследования - расчёт теплового состояния ТАБ при воздействии экстремальных температур в данном регионе. Методология и методы. Методом исследования является создание модели системы термостатирования ТАБ, а также анализ климатических условий региона. Результаты и научная новизна. Температура эксплуатации оказывает влияние на эксплуатационные характеристики ЭТС, в частности на пробег на одном заряде, на степень уменьшения ёмкости в процессе эксплуатации, и другие технические параметры ТАБ. В свою очередь создание сложных схем охлаждения экономически нецелесообразно как при производстве, так и при обслуживании. Учитывая климатические условия нашей страны, выбираются возможные регионы эксплуатации. В статье приведена последовательность выбора расчётных случаев для имитационной модели. После определения конструкции и параметров подогрева ТАБ был частично использован полный факторный эксперимент для оценки эффективности системы термостатирования с пассивным охлаждением. Разрядные токи, степень заряженности для единичного аккумулятора были получены при моделировании работы и состояния компонентов тягового электрического оборудования, в том числе ТАБ при моделировании движения ЭТС. Практическая значимость. В статье освещена проблематика безопасной продолжительной эксплуатации, а также указаны оптимальные, рабочие и критические диапазоны температур при эксплуатации единичных литий-ионных...
BACKGROUND: At the present moment there become more electrobuses in big towns, and the problem of the increasing the their energy efficiency is actual in intertown traffic (that assumes stops and time limitation among stops) because of the limitated on-board capacitors. AIMS: Development of the control signal algorithm of the accelerator pedal providing an effective energy consumption by an electrobus traction gear. METHODS: The new method for control signal formation of the accelerator pedal is proposed. It has a feature that provides the system operation traction gear frequency converter in zone of the increased efficiency factor and limits the velocity of control signal level growing when a driver tromps gas. RESULTS: Analysis of the electrobus operation results in intertown traffic shows, that the aggregate average electric capacity, consumed at electrobus operating equipped with the energy saving systems, is less by 8,2% than at electrobus operating without energy-saving systems at the same conditions. The average efficiency factor of the traction gear frequency converter system of an electrobus equipped with energy-saving systems has been increased by 4.5%. The time of driving on the route of an electrobus equipped with energy saving systems increased by 27 seconds that is an acceptable result. Energy saving in linehaul operation was provided only by an antislip system operation. During the total time driving of the electrobus energy saving was 2.6%. CONCLUSIONS: A new method for generating a control signal from the side of the accelerator pedal is proposed, which differs in that it ensures the operation of the traction motor frequency converter system in the zone of increased efficiency and limits the rate of increase in the level of the control action when the driver abruptly presses the accelerator pedal.
The article describes types of traction e-motors used in the leading wheel drive of battery electric passenger vehicles produced by different international manufacturers at the present time. The article analyzes European and Asian models of electric buses and shows a significantly increased use of different types of synchronous electric vehicles with rare-earth permanent magnets. The article analyzes drive kinematic systems used at the present, such as the ones with a single centre motor and with motors for driving each leading wheel. The range for specific powers of vehicles, as well as the most probable average value of specific powers, are determined. Electric buses with multi-motor drives and high maximum driving speeds (more than 70 km/h) have large values of specific powers. The article contains values of specific powers for traction electric motors at the rate from 0.75 to 3 kW /kg. The article describes motor operating conditions and determines the most probable operating modes. It concludes about the most optimal use of synchronous motors in the drive energized by high-quality rare-earth permanent magnets in terms of their maximum efficiency, overall dimensions and specific energy characteristics under these conditions.
The article presents conclusions about the possibility of self-oscillation, the results of field tests of the KAMAZ 6282 large class electric bus, the theoretical foundations for constructing an algorithm for monitoring wheel slip in braking mode with the function of self-oscillation suppression, as well as the results of mathematical modeling of its functioning in Matlab Simulink. The practical value of the research lies in the possibility of using the proposed control algorithm to develop a traffic control system for transport vehicles. Keywords: self-oscillation, braking, sliding, tire, observer, oscillation amplitude, energy efficiency, ABS
BACKGROUND: When a vehicle is in motion, self-oscillations which properties are dependent on slip rate in a contact patch may occur in the area of tire interaction with ground surface. Oscillations frequency will vary in dependence with value of wheel slip relative to ground surface. Soft self-oscillations are excited by variable set of initial conditions at full slip in traction and driven wheel rolling modes as well as in mixed braking mode with partial slip. Hard mode of self-oscillations occurs at full wheel slip in braking mode. These processes have a negative impact on the processes in electric drive and mechanical drivetrain reducing their efficiency and may cause damage of components. Oscillations in the system are excited by interaction forces of an elastic tire with ground surface featuring vertical oscillations due to elastic behavior of its interaction with road unevenness. AIMS: Research of features of oscillating process behavior in the nonlinear system of individual traction drive of an electrobus. METHODS: Simulation of self-oscillation excitation processes in the area of contact interaction of a wheel and road was carried out in the MATLAB/Simulink software package. RESULTS: The article features the results of simulation and experimental studies of self-oscillation excitation processes of the KAMAZ 6282 electrobus moving on asphalt-concrete surface. It was found that vertical wheel displacement when moving through unevenness lead to oscillating behavior of vertical reaction forces in contact patches and, as a consequence, to oscillating behavior of longitudinal reaction forces, torque and rotation velocity of the shaft of the traction electric motor of the individual drive. It was defined that tire oscillation frequency is 67 Hz that coincides with electric motor shaft rotation oscillation frequency and this value is the same for both experiment and simulation. CONCLUSIONS: Practical value of the study lies in ability of using the study results at development of self-oscillation processes exclusion algorithms as a part of vehicle control system.