When the tires interact with the road in contact, self-oscillations occur. The appearance of self-oscillations in the interaction zone can serve as a useful diagnostic sign of the development of the process of loss of adhesion in the work, cases of self-oscillations for an individual electric drive are investigated. In traction and driven modes, a "soft" mode of occurrence of self-oscillation of wheel rotation is possible. When braking, there is a "soft" mode of excitation of self-oscillations, and when the wheels are locked, a "hard" mode of self-oscillations of the translational movement of the wheel center. Keywords: self-oscillation; frictional interaction of the wheel with the base; "soft mode" of self-oscillation; "hard mode" of self-oscillation; Bendixon criterion; friction force; individual electric wheel drive
BACKGROUND: When a vehicle is in motion, self-oscillations which properties are dependent on slip rate in a contact patch may occur in the area of tire interaction with ground surface. Oscillations frequency will vary in dependence with value of wheel slip relative to ground surface. Soft self-oscillations are excited by variable set of initial conditions at full slip in traction and driven wheel rolling modes as well as in mixed braking mode with partial slip. Hard mode of self-oscillations occurs at full wheel slip in braking mode. These processes have a negative impact on the processes in electric drive and mechanical drivetrain reducing their efficiency and may cause damage of components. Oscillations in the system are excited by interaction forces of an elastic tire with ground surface featuring vertical oscillations due to elastic behavior of its interaction with road unevenness. AIMS: Research of features of oscillating process behavior in the nonlinear system of individual traction drive of an electrobus. METHODS: Simulation of self-oscillation excitation processes in the area of contact interaction of a wheel and road was carried out in the MATLAB/Simulink software package. RESULTS: The article features the results of simulation and experimental studies of self-oscillation excitation processes of the KAMAZ 6282 electrobus moving on asphalt-concrete surface. It was found that vertical wheel displacement when moving through unevenness lead to oscillating behavior of vertical reaction forces in contact patches and, as a consequence, to oscillating behavior of longitudinal reaction forces, torque and rotation velocity of the shaft of the traction electric motor of the individual drive. It was defined that tire oscillation frequency is 67 Hz that coincides with electric motor shaft rotation oscillation frequency and this value is the same for both experiment and simulation. CONCLUSIONS: Practical value of the study lies in ability of using the study results at development of self-oscillation processes exclusion algorithms as a part of vehicle control system.
The article refers to the lack of a system in the training of professional personnel, taking into account their potential for mental and physical development, the stability of the psycho-physiological state, motivation and other personal qualities of drivers. The issue of improving road safety by improving the system of training drivers of category "B" is being considered. Recommendations are presented for the advanced training program for taxi drivers to ensure the necessary level of road safety. Keywords: road safety, accident rate, traffic accident, driver training system, hardware and software complex, skill level, algorithm
The wheels of decelerating vehicles in braking mode roll with increased slip, up to complete lock-up, which is a negative phenomenon. This is effectively managed by the anti-lock braking system (ABS). However, in the course of braking, especially before the system activation, self-excited oscillatory processes with high amplitudes may occur, causing increased dynamic loads on the drive system. The paper studies the braking processes of a vehicle with an electromechanical individual traction drive in both electrodynamic regenerative and combined braking modes, utilizing the drive and the primary braking system. The theoretical framework is provided for identifying the self-excited oscillation onset conditions and developing a technique to detect wheel slips during braking to suppress these oscillations. To check the functionality of the wheel-slip observer in braking mode, the performance of the self-excited oscillation pulse suppression algorithm was studied in the MATLAB Simulink 2018b software package. The study results can be used to develop control systems equipped with the function of suppressing self-excited oscillations by vehicle motion.
The electric traction drive is increasingly being applied as a device providing traction force on driving wheels. This is due to its reliable torque transmission to the driving wheels, step-less regulation of the traction force on the driving wheels depending on the driving conditions, and increased design capabilities. In terms of power, the electric traction drive has maximum torque at low speeds, which internal combustion engines lack. This property of the electric drive is not applied in urban vehicles, as not all passengers are comfortable with intensive acceleration. In modern vehicles with an electric traction drive, the maximum acceleration can be limited by software, which is the focus of this study. This paper aims to develop an algorithm capable of recognizing when the permissible longitudinal acceleration exceeds the limit and generating an action to maintain the acceptable acceleration level. The electric traction drive of a large-class electric bus was used as a control object. An algorithm and a control law are hereby developed, which reduce longitudinal acceleration using PI control. Both simulation modeling and full-scale tests on the electric bus were carried out to evaluate the performance and efficiency of the algorithm. In this paper, the authors also introduce the cumulative velocity concept and prove the operability and efficiency of the developed method.
The article proposes a method of limiting the maximum speed of movement. An algorithm for designing an optimal controller that forms the required control action to limit the maximum speed is presented. The efficiency of the developed system is proved by mathematical modeling methods and field tests. Keywords: electric bus, traction electric drive, maximum speed, regulator coefficients