The investigation of component dynamics is one of the main tasks of internal combustion engine (ICE) simulation. This prediction is important in order to understand complex loading conditions, which happen in a running ICE. Due to the need for fuel saving, mechanical friction, in particular in radial slider bearings, is one important investigation target. A generic friction modeling approach for radial slider bearings, which can be applied to lubricated contact regimes, will be presented in this paper. Besides viscous friction, the approach considers in particular boundary friction. The parameterization of the friction model is done using surface material and surface roughness measurement data. Furthermore, fluid properties depending on the applied oil additives are being considered. The application of the model will be demonstrated for a typical engineering task of a connecting rod big end study to outline the effects of contact surface texture. AlSn-based and polymer coated bearing shells will be analyzed and compared with respect to friction reduction effects, running-in behavior and thermal load capabilities.
This study presents a new flexible dynamic model for drive systems comprising lubricated bearings operating under conditions representative of electrified vehicle powertrains. The multi-physics approach importantly accounts for the tribological phenomena at the roller–race conjunction and models their effect on shaft-bearing system dynamics. This is achieved by embedding a non-linear lubricated bearing model within a flexible system level model; this is something which has not, to the authors’ knowledge, been reported on hitherto. The elastohydrodynamic (EHL) film is shown to increase contact deflection, leading to increased contact forces and total bearing stiffness as rotational speeds increase. Results show that for a 68 Nm hub motor operating up to 21,000 rpm, the input bearing EHL film reaches a thickness of 4.15 m. The lubricant entrainment increases the roller–race contact deflection, causing the contact stiffness to increase non-linearly with speed. The contribution of the lubricant film leads to a 16.6% greater bearing stiffness at 21,000 rpm when compared to conventional dry-bearing modelling methods used in current multi-body dynamic software. This new methodology leads to more accurate dynamic response of high-speed systems necessary for the next generation of electrified vehicles.
24 January 2013 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
The authors have developed a coupled simulation methodology to target strong interactions between component dynamics, lubricated contacts and connecting oil supply lines in internal combustion engines. The dynamics of engine components, called bodies, is represented by a flexible multi-body approach. The mixed lubricated contacts between the component surfaces are represented by an averaged Reynolds equation considering an asperity contact model according to Greenwood and Tripp. The connections between oil bores are modelled by an oil supply line network. Within the network straight cylindrical lines are considered. The oil is assumed to be incompressible with isothermal viscosity. The flow in each line is described by a steady-state one-dimensional Euler equation, i.e. Bernoulli equation. Fictitious force effects, which result from the motion of the enclosing component, and cavitation effects are considered. The article discusses in particular the theory and the implementation of the oil supply line network as well as its coupling to the multi-body system and the hydrodynamic equations. Furthermore, the validation of the oil line model is presented. This is done via comparison with an equivalent three-dimensional computational fluid dynamics simulation. Finally, an application is shown for a single-cylinder internal combustion engine. All bodies of the model are represented to be flexible. Oil supply lines connect the big end bearing with one main bearing and with the small end bearing.
This paper presents a transient mixed-lubrication hydrodynamic and gas flow simulation model for a piston ring pack for a four-stroke internal combustion engine. The analyses carried out compare two fuel types, hydrogen and gasoline, at a 2000 rpm low engine load (20%), as well as 3000 rpm low (20%) and high (100%) engine loads, to investigate the effects of the different fuels and loading conditions on the ring pack. In particular, the minimum oil film thickness at the top compression ring, the total ring friction of the ring pack, the friction power loss and the blow-by are studied. The simulation shows that, under the high load conditions at 3000 rpm, the hydrogen variant exhibits larger friction power losses, around a 200 W peak difference and larger blow-by throughout the expansion stroke of the engine cycle. A similar trend can be observed for the low loads, where larger friction power losses with peak differences of 30 W and 40 W for 2000 rpm and 3000 rpm, respectively, are observed. The blow-by results for the low load at 2000 rpm show a slight increase of approximately 22% more gas flow into the crankcase, while the 3000 rpm simulation shows a 50% increase in blow-by for the hydrogen variant at low load and a 40% increase at high load. The findings that are presented indicate that, although alternative fuel sources such as hydrogen are very attractive alternatives to fossil fuels such as gasoline, there can be unwanted side effects that could lead to the permanent damage of components through quicker wear or hydrogen embrittlement from the blow-by gas.