The conversion of biogenic residues to fuels and chemicals via gasification and synthesis processes is a promising pathway to replace fossil carbon. In this study, the focus is set on sewage sludge gasification for syngas production. Experiments were carried out in a 20 kW fuel input bubbling fluidized bed facility with steam and oxygen as gasification agent. In-situ produced sewage sludge ash was used as bed material. The sensitivity of the key operation parameters gasifier temperature, oxygen ratio, steam to carbon ratio, and the space velocity on the syngas composition (H₂, CO, CO₂, CH₄, C_xH_y, H₂S, COS, NH₃, and tars) was determined. The results show that the produced syngas has high H₂ and CO concentrations of up to 0.37 m³ m⁻³ and 0.18 m³ m⁻³, respectively, and is thus suitable for synthesis of fuels and chemicals. By adjusting the steam to carbon ratio, the syngas’ H₂ to CO ratio can be purposely tailored by the water gas shift reaction for various synthesis products, e.g., synthetic natural gas (H₂/CO = 3) or Fischer–Tropsch products (H₂/CO = 2). Also, the composition and yields of fly ash and bed ash are presented. Through the gasification process, the cadmium and mercury contents of the bed ash were drastically reduced. The ash is suitable as secondary raw material for phosphorous or phosphate fertilizer production. Overall, a broad database was generated that can be used for process simulation and process design.

Finding a way for mitigating climate change is one of the main challenges of our generation. Sorption-enhanced gasification (SEG) is a process by which syngas as an important intermediate for the synthesis of e.g., dimethyl ether (DME), bio-synthetic natural gas (SNG) and Fischer–Tropsch (FT) products or hydrogen can be produced by using biomass as feedstock. It can, therefore, contribute to a replacement for fossil fuels to reduce greenhouse gas (GHG) emissions. SEG is an indirect gasification process that is operated in a dual-fluidized bed (DFB) reactor. By the use of a CO₂-active sorbent as bed material, CO₂ that is produced during gasification is directly captured. The resulting enhancement of the water–gas shift reaction enables the production of a syngas with high hydrogen content and adjustable H₂/CO/CO₂-ratio. Tests were conducted in a 200 kW DFB pilot-scale facility under industrially relevant conditions to analyze the influence of gasification temperature, steam to carbon (S/C) ratio and weight hourly space velocity (WHSV) on the syngas production, using wood pellets as feedstock and limestone as bed material. Results revealed a strong dependency of the syngas composition on the gasification temperature in terms of permanent gases, light hydrocarbons and tars. Also, S/C ratio and WHSV are parameters that can contribute to adjusting the syngas properties in such a way that it is optimized for a specific downstream synthesis process.

This research investigated the application of palm shell char as a catalyst for the catalytic steam reforming of tar after the sorption enhanced gasification (SEG) process. The catalytic activities of palm shell char and metal-supported palm shell char were tested in a simulated SEG derived syngas with tar model compounds (i.e., toluene and naphthalene) at a concentration of 10 g m⁻³ _NTP. The results indicated that palm shell char had an experimentally excellent catalytic activity for tar reforming with toluene and naphthalene conversions of 0.8 in a short residence time of 0.17 s at 900 °C. A theoretical residence time to reach the complete naphthalene conversion was 1.2 s at 900 °C for palm shell char, demonstrating a promising activity similar to wood char and straw char, but better than CaO. It was also found that potassium and iron-loaded palm shell chars exhibited much better catalytic activity than palm shell char, while the parallel reaction of gasification of K-loaded palm shell char influenced the conversion with its drastic mass loss. Moreover, contrary to CaO, palm shell char presented relatively low selectivity to benzene, and its spontaneous gasification generated extra syngas. In summary, the present study demonstrated that the low-cost material, palm shell char, can successfully be used as the tar-reforming catalyst after SEG process.