A “digital twin” is a dynamic, digital replica of a technical object (e.g., a physical system, device, machine or production process) or a living organism. Using this type of solution has become an integral part of Industry 4.0, offering businesses tangible benefits, in addition to being particularly effective within the context of sustainable production and maintenance. The purpose of this paper is to present the results of research on the development of digital twins of technical objects, which involved data acquisition and their conversion into knowledge, the use of physical models to simulate tasks and processes, and the use of simulation models to improve the physical tasks and processes. In addition, monitoring processes and process parameters allow for the continued improvement of existing processes as regards intelligent eco-designing and planning and monitoring production processes while taking into account sustainable production and maintenance.

While the intensity, complexity, and specificity of robotic exercise may be supported by patient-tailored three-dimensional (3D)-printed solutions, their performance can still be compromised by non-optimal combinations of technological parameters and material features. The main focus of this paper was the computational optimization of the 3D-printing process in terms of features and material selection in order to achieve the maximum tensile force of a hand exoskeleton component, based on artificial neural network (ANN) optimization supported by genetic algorithms (GA). The creation and 3D-printing of the selected component was achieved using Cura 0.1.5 software and 3D-printed using fused filament fabrication (FFF) technology. To optimize the material and process parameters we compared ten selected parameters of the two distinct printing materials (polylactic acid (PLA), PLA+) using ANN supported by GA built and trained in the MATLAB environment. To determine the maximum tensile force of the exoskeleton, samples were tested using an INSTRON 5966 universal testing machine. While the balance between the technical requirements and user safety constraints requires further analysis, the PLA-based 3D-printing parameters have been optimized. Additive manufacturing may support the successful printing of usable/functional exoskeleton components. The network indicated which material should be selected: Namely PLA+. AI-based optimization may play a key role in increasing the performance and safety of the final product and supporting constraint satisfaction in patient-tailored solutions.

Technological and material issues in 3D printing technologies should take into account sustainable development, use of materials, energy, emitted particles, and waste. The aim of this paper is to investigate whether the sustainability of 3D printing processes can be supported by computational intelligence (CI) and artificial intelligence (AI) based solutions. We present a new AI-based software to evaluate the amount of pollution generated by 3D printing systems. We input the values: printing technology, material, print weight, etc., and the expected results (risk assessment) and determine if and what precautions should be taken. The study uses a self-learning program that will improve as more data are entered. This program does not replace but complements previously used 3D printing metrics and software.

3D printing of assistive devices requires optimization of material selection, raw materials formulas, and complex printing processes that have to balance a high number of variable but highly correlated variables. The performance of patient-specific 3D printed solutions is still limited by both the increasing number of available materials with different properties (including multi-material printing) and the large number of process features that need to be optimized. The main purpose of this study is to compare the optimization of 3D printing properties toward the maximum tensile force of an exoskeleton sample based on two different approaches: traditional artificial neural networks (ANNs) and a deep learning (DL) approach based on convolutional neural networks (CNNs). Compared with the results from the traditional ANN approach, optimization based on DL decreased the speed of the calculations by up to 1.5 times with the same print quality, improved the quality, decreased the MSE, and a set of printing parameters not previously determined by trial and error was also identified. The above-mentioned results show that DL is an effective tool with significant potential for wide application in the planning and optimization of material properties in the 3D printing process. Further research is needed to apply low-cost but more computationally efficient solutions to multi-tasking and multi-material additive manufacturing.

Three-dimensional-printed medical devices are a separate group of medical devices necessary for the development of personalized medicine. The present article discusses a modern and specific group of medical devices and exoskeletons, which aims to present our own experiences in the selection of materials, design, artificial-intelligence optimization, production, and testing of several generations of various upper limb exoskeletons when considering the Medical Devices Regulation (MDR) and the ISO 13485 and ISO 10993 standards. Work is underway to maintain the methodological rigor inherent in medical devices and to develop new business models to achieve cost-effectiveness so that inadequate legislation does not stop the development of this group of technologies (3D scanning, 3D printing, and reverse engineering) in the healthcare system. The gap between research and engineering practice and clinical 3D printing should be bridged as quickly and as carefully as possible. This measure will ensure the transfer of proven solutions into clinical practice. The growing maturity of 3D printing technology will increasingly impact everyday clinical practice, so it is necessary to prepare medical specialists and strategic and organizational changes to realize the correct implementation based on the needs of patients and clinicians.

In this paper, the application of multi-agent system to support decision-making process in design for recycling is presented. The design for recycling term is highlighted either as the design problem or from the point of view of regulations. The structure of agent system supporting the designer during the design process is showed. The basis of special kind of product model, that is the extension of standard 3D product model, called recycling-oriented product model, is described. The example results of analysis, based on real household appliance model, are presented.