It is of great importance for pipeline systems to be is efficient, cost-effective and safe during the transportation of the liquids and gases. However, underground pipelines often experience leaks due to corrosion, human destruction or theft, long-term Earth movement, natural disasters and so on. Leakage or explosion of the operating pipeline usually cause great economical loss, environmental pollution or even a threat to citizens, especially when these accidents occur in human-concentrated urban areas. Therefore, the surveying of the routed pipeline is of vital importance for the Pipeline Integrated Management (PIM). In this paper, a comprehensive review of the Micro-Inertial Measurement Unit (MIMU)-based intelligent Pipeline Inspection Gauge (PIG) multi-sensor fusion technologies for the transport of liquids and gases purposed for small-diameter pipeline (D < 30 cm) surveying is demonstrated. Firstly, four types of typical small-diameter intelligent PIGs and their corresponding pipeline-defects inspection technologies and defects-positioning technologies are investigated according to the various pipeline defects inspection and localization principles. Secondly, the multi-sensor fused pipeline surveying technologies are classified into two main categories, the non-inertial-based and the MIMU-based intelligent PIG surveying technology. Moreover, five schematic diagrams of the MIMU fused intelligent PIG fusion technology is also surveyed and analyzed with details. Thirdly, the potential research directions and challenges of the popular intelligent PIG surveying techniques by multi-sensor fusion system are further presented with details. Finally, the review is comprehensively concluded and demonstrated.
The conventional temperature drift error (TDE) compensation model cannot decouple temperature dependence of Si-based materials because temperature correlated quantities (TCQ) have not been obtained comprehensively, and Micro-Electro-Mechanical System gyros’ (MEMS-gyros’) environmental adaptability is reduced in diverse, complicated conditions. The study presents modification of TDE compensation model of MEMS-gyros based on microstructure thermal effect analysis (MTEA). First, Si-based materials’ temperature dependence was studied in microstructure with thermal expansion effect and TCQ that determines the structural deformation were extracted to modify the conventional model, including temperature variation and its square. Second, a precise TDE test method was formed by analyzing heat conduction process between MEMS-gyros and thermal chamber, and temperature experiments were designed and conducted. Third, the modified model’s parameters were identified based on radical basis function artificial neural network (RBF ANN) and its performance was evaluated. Last, the conventional and modified models were compared in performance. The experimental results show MEMS-gyros’ bias stability was up to 10% of the conventional model, the temperature dependence of Si-based materials was decoupled better by the modified one and the environmental adaptability of MEMS-gyros was improved to expand their application in diverse complicated conditions.
The Global Navigation Satellite Systems (GNSS) becomes the primary choice for device localization in outdoor situations. At the same time, many applications do not require precise absolute Earth coordinates, but instead, inferring the geometric configuration information of the constituent nodes in the system by relative positioning. The Real-Time Kinematic (RTK) technique shows its efficiency and accuracy in calculating the relative position. However, when the cycle slips occur, the RTK method may take a long time to obtain a fixed ambiguity value, and the positioning result will be a “float” solution with a low meter accuracy. The novel method presented in this paper is based on the Relative GNSS Tracking Algorithm (Regtrack). It calculates the changes in the relative baseline between two receivers without an ambiguity estimation. The dead reckoning method is used to give out the relative baseline solution while a parallel running Extended Kalman Filter (EKF) method reinitiates the relative baseline when too many validation failures happen. We conducted both static and kinematic tests to assess the performance of the new methodology. The experimental results show that the proposed strategy can give accurate millimeter-scale solutions of relative motion vectors in adjacent two epochs. The relative baseline solution can be sub-decimeter level with or without the base station is holding static. In the meantime, when the initial tracking point and base station coordinates are precisely obtained, the tracking result error can be only 40 cm away from the ground truth after a 25 min drive test in an urban environment. The efficiency test shows that the proposed method can be a real-time method, the time that calculates one epoch of measurement data is no more than 80 ms and is less than 10 ms for best results. The novel method can be used as a more robust and accurate ambiguity free tracking approach for outdoor applications.
The steady airflow field on a ship is affected by structure and motion and challenged by phenomena such as the low measurement accuracy of the wind field caused by the occlusion of the anemometer. In this work, an improvement in the accuracy of wind measurements affected by structure is proposed, and a method for combining anemometer and X-band marine radar (RCRF) data is designed to further obtain wind parameters. The first step is to use the multivariate bias strategy to achieve the optimal layout of multiple anemometers based on computational fluid dynamics (CFD) numerical simulation data. Then, random forest (RF) is employed to train the wind parameter estimation model. Finally, the wind parameters are optimally estimated by combining the anemometer with the X-band radar. Under the ideal simulation, noise, and temporal uncertainty combined with anemometer noise conditions, the RCRF algorithm performance is evaluated. Compared with the bias correction combination four-anemometer weighted fusion algorithm (FAF-BC) and the BP neural network algorithm for radar wind measurement combination (RCBP), the mean errors in wind direction and speed are reduced by 1.99° and 6.99% at most. The maximum errors are reduced by 14.46° and 15.81% at most, respectively.
The medium-voltage direct-current (MVDC) ship power system has been extensively investigated and discussed in recent years. This paper presents an alternating current/direct-current (AC/DC) power flow algorithm based on complex affine arithmetic for the zonal MVDC shipboard power system in the presence of power variation. The power converter effect is considered, and an affine power converter model is proposed in the power flow model. An affine-analysis-based sequential method is adopted to solve AC/DC power flows. With the proposed algorithm, the bounds of bus voltages can be effectively obtained. A relative influence factor is defined to quantitatively assess the effect of power variation on voltage profile. Four cases are studied in detail to demonstrate the applicability of the proposed algorithm. The proposed algorithm is useful in network architecture design, planning, and online operations of MVDC power systems when such decisions are subject to power variation.