Vikram Yadama

Prof. Vikram Yadama

Department of Civil & Environmental Engineering, Composite Materials and Engineering Center, Washington State University, Paccar 154, 2001 East Grimes Way, Pullman, WA 99164, USA

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 July 2013 in Wood Science and Technology
Verified
Journal Article
Closed access
PDF file
MPManuel Raul Pelaez-Samaniego
Manuel Raul Pelaez-Samaniego
Vikram YadamaVikram Yadama
Vikram Yadama
ELEini Lowell
Eini Lowell
RERaul Espinoza-Herrera
Raul Espinoza-Herrera

1 September 2014 in Journal of Analytical and Applied Pyrolysis
Verified
Journal Article
Closed access
MPManuel Raul Pelaez-Samaniego
Manuel Raul Pelaez-Samaniego
Vikram YadamaVikram Yadama
Vikram Yadama
MGManuel Garcia-Perez
Manuel Garcia-Perez
ELEini Lowell
Eini Lowell
AMArmando G. McDonald
Armando G. McDonald

4 September 2012 in Holzforschung
Verified
Journal Article
Closed access
MPManuel Raul Pelaez-Samaniego
Manuel Raul Pelaez-Samaniego
Vikram YadamaVikram Yadama
Vikram Yadama
ELEini Lowell
Eini Lowell
TAThomas E. Amidon
Thomas E. Amidon
TCTimothy L. Chaffee
Timothy L. Chaffee
Undebarked ponderosa pine chips were treated by hot water extraction to modify the chemical composition. In the treated pine (TP), the mass was reduced by approximately 20%, and the extract was composed mainly of degradation products of hemicelluloses. Wood flour produced from TP and unextracted chips (untreated pine, UP) was blended with high-density polyethylene (HDPE) and polypropylene (PP) and was extruded into wood plastic composites (WPCs). Formulations for WPCs consisted of 58% pine, 32% plastic, and 10% other additives. WPC based on HDPE+TP and PP+TP absorbed 46–45% less water than did WPC based on HDPE+UP and PP+UP, respectively. Thickness swelling was reduced by 45–59%, respectively, after 2520 h of immersion. The diffusion constant decreased by approximately 36%. Evaluation of mechanical properties in flexure and tension mode indicated improvements in TP-WPC properties, although the data were not statistically significant in all cases. Results showed that debarking of ponderosa pine is not required for WPC production.

1 June 2017 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
RZRui Zhu
Rui Zhu
Vikram YadamaVikram Yadama
Vikram Yadama
HLHang Liu
Hang Liu
RLRichard J.T. Lin
Richard J.T. Lin
David Paul HarperDavid Paul Harper
David Paul Harper

19 February 2014 in Holzforschung
Verified
Journal Article
Open access
MPManuel Raul Pelaez-Samaniego
Manuel Raul Pelaez-Samaniego
Vikram YadamaVikram Yadama
Vikram Yadama
TGTsai Garcia-Perez
Tsai Garcia-Perez
ELEini Lowell
Eini Lowell
TAThomas Amidon
Thomas Amidon
The affinity of particleboard (PB) to water is one of the main limitations for using PB in moisture-rich environments. PB dimensional stability and durability can be improved by reducing the available hydroxyl groups in wood through hemicellulose removal, for example, by hot water extraction (HWE), which increases wood resistance to moisture uptake. The resulting liquid fraction from HWE is rich in hemicelluloses and can be used for chemicals and fuels, and the solid fraction is less hydrophilic. The objective of this study was to investigate the effects of HWE of softwood chips (conducted at 160°C and 90 min) and hardwood chips (160°C and 120 min) on the properties of PB panels. HWE increased compressibility and reduced springback by 34% and 44% for pine and maple chips, respectively, which positively impacted the PB properties. Water absorption of pine PB panels was lowered by 35% and that of maple PB panels by 30%, while reduction of thickness swelling was lowered by 39% for pine PB and 56% for maple PB after 24 h of immersion in water. The mechanical properties were not significantly affected.

20 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
MMMostafa Mohammadabadi
Mostafa Mohammadabadi
Vikram YadamaVikram Yadama
Vikram Yadama
DDDaniel Dolan
Daniel Dolan
During this study, full-size wood composite sandwich panels, 1.2 m by 2.4 m (4 ft by 8 ft), with a biaxial corrugated core were evaluated as a building construction material. Considering the applications of this new building material, including roof, floor, and wall paneling, sandwich panels with one and two corrugated core(s) were fabricated and experimentally evaluated. Since primary loads applied on these sandwich panels during their service life are live load, snow load, wind, and gravity loads, their bending and compression behavior were investigated. To improve the thermal characteristics, the cavities within the sandwich panels created by the corrugated geometry of the core were filled with a closed-cell foam. The R-values of the sandwich panels were measured to evaluate their energy performance. Comparison of the weight indicated that fabrication of a corrugated panel needs 74% less strands and, as a result, less resin compared to a strand-based composite panel, such as oriented strand board (OSB), of the same size and same density. Bending results revealed that one-layer core sandwich panels with floor applications under a 4.79 kPa (100 psf) bending load are able to meet the smallest deflection limit of L/360 when the span length (L) is 137.16 cm (54 in) or less. The ultimate capacity of two-layered core sandwich panels as a wall member was 94% and 158% higher than the traditional walls with studs under bending and axial compressive loads, respectively. Two-layered core sandwich panels also showed a higher ultimate capacity compared to structural insulated panels (SIP), at 470% and 235% more in bending and axial compression, respectively. Furthermore, normalized R-values, the thermal resistance, of these sandwich panels, even with the presence of thermal bridging due to the core geometry, was about 114% and 109% higher than plywood and oriented strand board, respectively.