wenkai yue

Dr. wenkai yue

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 February 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
WYwenkai yue
wenkai yue
RLRuixuan Liu
Ruixuan Liu
PLpeixian li
peixian li
XZXiaowei Zhou
Xiaowei Zhou
YLY Liu
Y Liu
XWXiaowei Wang
Xiaowei Wang
In this paper, the X-ray diffraction full width at half the maximum (XRD FWHM) of a 3.5 µm-thick hydride vapor phase epitaxy-aluminum nitride (HVPE-AlN) (002) face after high-temperature annealing was reduced to 129 arcsec. The tensile strain in the HVPE-AlN samples gradually released with the increasing annealing temperature. When the annealing temperature exceeded 1700 °C, an aluminum oxynitride (AlON) region was generated at the contact interface between HVPE-AlN and sapphire, and the AlON structure was observed to conform to the characteristics of Al5O6N by high-resolution transmission electron microscopy (HRTEM). A 265 nm light-emitting diode (LED) based on an HVPE-AlN template annealed at 1700 °C achieved a light output power (LOP) of 4.48 mW at 50 mA, which was approximately 57% greater than that of the original sample.

1 January 2022 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
WYwenkai yue
wenkai yue
ZLZhimin Li
Zhimin Li
PLpeixian li
peixian li
XZXiaowei Zhou
Xiaowei Zhou
YWYanli Wang
Yanli Wang
JBJunchun Bai
Junchun Bai

10 June 2021 in IEEE Photonics Journal
Verified
Journal Article
Open access
YWYanli Wang
Yanli Wang
PLPeixian Li
Peixian Li
SJSiyu Jiang
Siyu Jiang
XZXiaowei Zhou
Xiaowei Zhou
JWJinxing Wu
Jinxing Wu
YHYue Hao
Yue Hao
The lower luminous efficiency is a critical issue for ultraviolet light-emitting diodes (UV-LEDs) owing to the poor carrier injection efficiency and high dislocation density. Here, we can improve the luminous efficiency in two avenues by adjusting the Al composition of the InGaN/AlxGa1-xN pre-well superlattice. First, due to the strain-induced piezoelectric and intrinsic spontaneous polarization, a large number of electrons gather at the InGaN/AlxGa1-xN interface, which improves the electron concentration of the pre-well superlattice and lowers the conduction band energy of the first quantum barrier layer (FQB), thus enhancing the electron injection efficiency. Second, the pre-well superlattice can act as a hole blocking layer to prevent holes from leaking into the n-type layer and confine them in the quantum well layer. As the Al composition increases, the hole blocking effect of the pre-well superlattice is strengthened. However, higher Al composition decreases the lattice quality, which makes it possible for carrier loss through defect-related non-radiative recombination. Finally, the output power of the samples with 5% Al composition in the pre-well superlattice is 5.9% and 102.5% higher than that of the samples with 3% and 7% Al composition, respectively.

17 January 2020 in Materials
Verified
Journal Article
Open access
PDF file
YWYanli Wang
Yanli Wang
PLpeixian li
peixian li
XZXinyu Zhang
Xinyu Zhang
SXShengrui Xu
Shengrui Xu
XZXiaowei Zhou
Xiaowei Zhou
YHYue Hao
Yue Hao
To obtain excellent current spreading performance of ultraviolet light-emitting diodes (UVLEDs), a 60-period stacked Si modulation-doped n-AlGaN/u-GaN structure is proposed to replace the traditional n-AlGaN structure. The high-resolution X-ray diffraction ω-scan rocking curves show that the periodic growth of AlGaN and GaN layers plays a positive role in reducing dislocation density. Compared with the conventional UV light-emitting diodes (LEDs), light emission micrographs of devices with a multi-layer stacked n-AlGaN/u-GaN structure reveal higher brightness and a more uniform distribution. In addition, the output power and external quantum efficiency under a 20-mA injection current are increased by 22% and 26.5%, respectively. Experimental and simulation results indicate that a multi-layer stacking structure can alleviate the current crowding effect in four ways: (1) a reduction in dislocation density; (2) replacement of quasi-two-dimensional electron transport with electronic bulk transport to enhance electron mobility; (3) an increase in electron concentration without improving the impurity concentration; and (4) a weakening of the electron scattering effect by reducing the impurity concentration.

5 August 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
WYwenkai yue
wenkai yue
PLpeixian li
peixian li
XZXiaowei Zhou
Xiaowei Zhou
YWYanli Wang
Yanli Wang
JWJinxing Wu
Jinxing Wu
JBJunchun Bai
Junchun Bai
In this paper, the conditions of the dip-coating method of SiO2 nanospheres are optimized, and a neatly arranged single-layer SiO2 array is obtained. On this basis, a “top-down” inductively coupled plasma (ICP) technique is used to etch the p-GaN layer to prepare a periodic triangular nanopore array. After the etching is completed, the compressive stress in the epitaxial wafer sample is released to a certain extent. Then, die processing is performed on the etched LED epitaxial wafer samples. The LED chip with an etching depth of 150 nm has the highest overall luminous efficiency. Under a 100 mA injection current, the light output power (LOP) of the etched 150 nm sample is 23.61% higher than that of the original unetched sample.

13 November 2020 in Materials
Verified
Journal Article
Open access
PDF file
JWJinxing Wu
Jinxing Wu
PLpeixian li
peixian li
SXShengrui Xu
Shengrui Xu
XZXiaowei Zhou
Xiaowei Zhou
HTHongchang Tao
Hongchang Tao
YHYue Hao
Yue Hao
Magnetron sputtering is adopted to deposit ~25 nm thick AlN on the surface of hexagonal BN(h-BN)/sapphire substrates, followed by epitaxial GaN growth on top of the AlN/h-BN/sapphire substrate using a metal–organic chemical vapor deposition system. Compared to GaN grown on the h-BN/sapphire surface directly, this method results in a continuous and smooth GaN film with a smaller root mean square roughness. Besides, the introduction of the sputtered AlN layer reduces the dislocation density of GaN by 35.7%. We provide a pathway of GaN epitaxy on the h-BN surface, which significantly improves its surface morphology and crystal quality.