peixian li

peixian li


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 February 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
WYwenkai yue
wenkai yue
RLRuixuan Liu
Ruixuan Liu
PLpeixian li
peixian li
XZXiaowei Zhou
Xiaowei Zhou
YLY Liu
Y Liu
XWXiaowei Wang
Xiaowei Wang
In this paper, the X-ray diffraction full width at half the maximum (XRD FWHM) of a 3.5 µm-thick hydride vapor phase epitaxy-aluminum nitride (HVPE-AlN) (002) face after high-temperature annealing was reduced to 129 arcsec. The tensile strain in the HVPE-AlN samples gradually released with the increasing annealing temperature. When the annealing temperature exceeded 1700 °C, an aluminum oxynitride (AlON) region was generated at the contact interface between HVPE-AlN and sapphire, and the AlON structure was observed to conform to the characteristics of Al5O6N by high-resolution transmission electron microscopy (HRTEM). A 265 nm light-emitting diode (LED) based on an HVPE-AlN template annealed at 1700 °C achieved a light output power (LOP) of 4.48 mW at 50 mA, which was approximately 57% greater than that of the original sample.

1 March 2025 in Applied Physics Reviews
Verified
Journal Article
Closed access
CCChao Chen
Chao Chen
TZTao Zhang
Tao Zhang
CZChunfu Zhang
Chunfu Zhang
JFJiatong Fan
Jiatong Fan
LZLe Zhang
Le Zhang
YHYue Hao
Yue Hao
Wide bandgap semiconductor (WBS) materials have a wide range of applications in radio frequency and power electronics due to their many advantages such as high saturation drift velocity, breakdown voltage, and excellent thermal/chemical stability. Diamond, Ga2O3, GaN, and SiC are typical WBS materials. Reliability studies for these four materials and devices are crucial for WBS applications. Traditional means of reliability studies include, but are not limited to, x-ray diffraction, atomic force microscopy, Raman spectroscopy, and electron microscopy et al. However, most of these methods are ex situ studies after material or device failure and thus have some limitations. In situ transmission electron microscope (TEM) is a favorable technology to observe the degradation and failure process of materials and devices in real time, which may provide effective guidance in material growth, device structure design, device process optimization, and reliability improvement. In recent years, in situ TEM technology has been gradually used by researchers to study WBS materials and devices. In this review, we present a comprehensive and systematic review of in situ TEM works on diamond, Ga2O3, GaN, and SiC materials and devices, with a particular focus on the progress of the technology in the reliability study of such materials and devices. While summarizing the advantages of in situ TEM in the investigation of WBS materials and devices, the review also looks forward to the future of in situ TEM in promoting the study of WBS materials and devices.

18 December 2023 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
YSYanan Sun
Yanan Sun
JZJiejie Zhu
Jiejie Zhu
WYWenhui Yi
Wenhui Yi
YWYuxiang Wei
Yuxiang Wei
XZXuejiao Zhou
Xuejiao Zhou
XMXiaohua Ma
Xiaohua Ma
For over half a century, traditional silicon-based integrated circuits (ICs) have been the basis of computational electronics and are widely used in computers, cell phones, and other fields. With the rapid development of human society, silicon-based semiconductor technology is approaching its physical and engineering limits. Our increasing diversity of non-traditional computing needs, such as ultra-small, ultra-fast, ultra-low-power wearables, and space radiation protection, is driving the search for new electronic materials. Semiconducting single-walled carbon nanotubes (s-SWCNTs) have many excellent electrical properties, such as high carrier mobility and high ballistic transport, making them strong candidates for new semiconductor materials in the post-Moore era. Carbon-based electronic technology has been developed for over 20 years, and the fundamental issues such as the material purification of s-SWCNTs, preparation prospects of s-SWCNT-based field-effect transistors (CNT FETs), and device physics based on CNT FETs have been basically solved. However, the chiral diversity of s-SWCNTs may lead to problems such as fluctuations in the electrical performance of CNT FETs, limiting the application of s-SWCNTs in high-end ICs. Monochiral s-SWCNTs not only have excellent electrical properties but also have a controllable structure and uniformity, which are crucial for the high-end IC of CNTs. However, some problems exist in the purity and yield of monochiral s-SWCNT preparation and the optimization of monochiral CNT FETs. Therefore, the chiral sorting of CNTs is reviewed in this paper, and the progress of polymer reprocessing in chiral separation is highlighted. Then, the research progress of monochiral CNT FETs is introduced, and possible development directions are summarized and analyzed. Finally, the application prospects of chiral-enriched s-SWCNTs include challenges and future opportunities.

11 February 2021 in IEEE Photonics Journal
Verified
Journal Article
Open access
JWJinxing Wu
Jinxing Wu
PLpeixian li
peixian li
XZXiaowei Zhou
Xiaowei Zhou
JWJiangtao Wu
Jiangtao Wu
YHYue Hao
Yue Hao
A 365 nm AlxGa1-xN-based ultraviolet light-emitting diodes (LEDs) with double Al composition gradient last quantum barrier and hole supply layer structure has been studied. Experimental results show that the proposed structure enhances the carrier injection efficiency and suppresses the overflow of electrons. The introduction of three-dimensional hole gas further enhances the hole injection efficiency. As a result, the wall plug efficiency and electroluminescence intensity are significantly improved. In addition, the carrier concentration and the radiative recombination rate in the active region of the quantum well increases. Looking at the energy band diagram, one sees that the double Al composition gradient structure leads to higher electron blocking and alleviates the hole blocking effect. Overall, we conclude that the double Al composition gradient structure provides a pathway to achieve high-efficiency ultraviolet LEDs.

25 August 2022 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
WHWenshuai Hu
Wenshuai Hu
YWYabin Wang
Yabin Wang
KHKexin He
Kexin He
XHXiaolong He
Xiaolong He
YBYan Bai
Yan Bai
YXYong Xie
Yong Xie
The atomically thin two-dimensional (2D) transition-metal dichalcogenide (e.g., MoS2) material can withstand large strains up to 11% to change its energy band structure, thereby further tuning its optical, electrical, and other physical properties. However, the slippage of 2D materials on substrate hammers the further strain tuning of the properties of 2D materials. Hereby, a facile three points approach combined with a dry transfer method that can apply uniaxial strain to two-dimensional materials is provided. The slippage of WSe2 on polycarbonate (PC) substrate can be suppressed by thermally annealing WSe2/PC in low pressure Ar atmosphere above 100 °C for 3 h. Straining cycle evolution experiments revealed that the thermal annealing of (1L) WSe2 could suppress slippage from the surface of the PC. The spectral gauge factor of 1L WSe2 is found to be around -60 meV/%. After thermal treatment, WSe2/PC stacking can survive in DI water for at least 24 h without the degradation of the spectral gauge factor. Dome structures are formed after thermal treatments with the interplay of the viscoelasticity and surface tension of the PC and the 0.4% tensile strain on WSe2, and the RMS roughness of WSe2/PC increased from 820 to 1292 pm, indicating that there could be larger lateral friction force to suppress slippage following thermal annealing. Our findings enrich the strain engineering of 2D materials and their device applications.

17 March 2014 in Science China Physics, Mechanics & Astronomy
Verified
Journal Article
Closed access
PDF file
YHYong Huang
Yong Huang
PLpeixian li
peixian li
ZYZhuo Yang
Zhuo Yang
YHYue Hao
Yue Hao
XWXiaoBo Wang
XiaoBo Wang