In this paper, the X-ray diffraction full width at half the maximum (XRD FWHM) of a 3.5 µm-thick hydride vapor phase epitaxy-aluminum nitride (HVPE-AlN) (002) face after high-temperature annealing was reduced to 129 arcsec. The tensile strain in the HVPE-AlN samples gradually released with the increasing annealing temperature. When the annealing temperature exceeded 1700 °C, an aluminum oxynitride (AlON) region was generated at the contact interface between HVPE-AlN and sapphire, and the AlON structure was observed to conform to the characteristics of Al5O6N by high-resolution transmission electron microscopy (HRTEM). A 265 nm light-emitting diode (LED) based on an HVPE-AlN template annealed at 1700 °C achieved a light output power (LOP) of 4.48 mW at 50 mA, which was approximately 57% greater than that of the original sample.
A 365 nm AlxGa1-xN-based ultraviolet light-emitting diodes (LEDs) with double Al composition gradient last quantum barrier and hole supply layer structure has been studied. Experimental results show that the proposed structure enhances the carrier injection efficiency and suppresses the overflow of electrons. The introduction of three-dimensional hole gas further enhances the hole injection efficiency. As a result, the wall plug efficiency and electroluminescence intensity are significantly improved. In addition, the carrier concentration and the radiative recombination rate in the active region of the quantum well increases. Looking at the energy band diagram, one sees that the double Al composition gradient structure leads to higher electron blocking and alleviates the hole blocking effect. Overall, we conclude that the double Al composition gradient structure provides a pathway to achieve high-efficiency ultraviolet LEDs.
In this study, we propose a polarized electron blocking layer (EBL) structure using AlxGa1−xN/AlxGa1−xN to enhance the internal quantum efficiency (IQE) of AlGaN-based ultraviolet light-emitting diodes (UV LEDs). Our findings indicate that this polarized EBL structure significantly improves IQE compared to conventional EBLs. Additionally, we introduce an electric-field reservoir (EFR) optimization method to maximize IQE. Specifically, optimizing the polarized EBL structure of AlxGa1−xN/AlxGa1−xN enhances the hole drift rate, resulting in an IQE improvement of 19% and an optical output power increase of 186 mW at a current of 210 mA.
The lower luminous efficiency is a critical issue for ultraviolet light-emitting diodes (UV-LEDs) owing to the poor carrier injection efficiency and high dislocation density. Here, we can improve the luminous efficiency in two avenues by adjusting the Al composition of the InGaN/AlxGa1-xN pre-well superlattice. First, due to the strain-induced piezoelectric and intrinsic spontaneous polarization, a large number of electrons gather at the InGaN/AlxGa1-xN interface, which improves the electron concentration of the pre-well superlattice and lowers the conduction band energy of the first quantum barrier layer (FQB), thus enhancing the electron injection efficiency. Second, the pre-well superlattice can act as a hole blocking layer to prevent holes from leaking into the n-type layer and confine them in the quantum well layer. As the Al composition increases, the hole blocking effect of the pre-well superlattice is strengthened. However, higher Al composition decreases the lattice quality, which makes it possible for carrier loss through defect-related non-radiative recombination. Finally, the output power of the samples with 5% Al composition in the pre-well superlattice is 5.9% and 102.5% higher than that of the samples with 3% and 7% Al composition, respectively.
To obtain excellent current spreading performance of ultraviolet light-emitting diodes (UVLEDs), a 60-period stacked Si modulation-doped n-AlGaN/u-GaN structure is proposed to replace the traditional n-AlGaN structure. The high-resolution X-ray diffraction ω-scan rocking curves show that the periodic growth of AlGaN and GaN layers plays a positive role in reducing dislocation density. Compared with the conventional UV light-emitting diodes (LEDs), light emission micrographs of devices with a multi-layer stacked n-AlGaN/u-GaN structure reveal higher brightness and a more uniform distribution. In addition, the output power and external quantum efficiency under a 20-mA injection current are increased by 22% and 26.5%, respectively. Experimental and simulation results indicate that a multi-layer stacking structure can alleviate the current crowding effect in four ways: (1) a reduction in dislocation density; (2) replacement of quasi-two-dimensional electron transport with electronic bulk transport to enhance electron mobility; (3) an increase in electron concentration without improving the impurity concentration; and (4) a weakening of the electron scattering effect by reducing the impurity concentration.
This work investigated the impact of periodic thickness and doping region on the doping efficiency of the P-type AlGaN superlattice. In this paper, the band structure of the simulated superlattice was analyzed. The superlattice structure of Al0.1Ga0.3N/Al0.4Ga0.6N, and the AlGaN buffer on the sapphire substrate, achieved a resistivity of ~3.3 Ω·cm. The results indicate that barrier doping and low periodic thickness offer significant advantages in introducing a reduction of the resistivity of P-type AlGaN superlattice structures.