Konstantinos Vontas

Mr. Konstantinos Vontas

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
KVKonstantinos Vontas
Konstantinos Vontas
MAManolia Andredaki
Manolia Andredaki
Anastasios GeorgoulasAnastasios Georgoulas
Anastasios Georgoulas
NMNicolas Miché
Nicolas Miché
Marco MarengoMarco Marengo
Marco Marengo

22 May 2020 in Fluids
Verified
Journal Article
Open access
PDF file
KVKonstantinos Vontas
Konstantinos Vontas
CBCristina Boscariol
Cristina Boscariol
Manolia AndredakiManolia Andredaki
Manolia Andredaki
Anastasios GeorgoulasAnastasios Georgoulas
Anastasios Georgoulas
Cyril CruaCyril Crua
Cyril Crua
Marco MarengoMarco Marengo
Marco Marengo
Liquid penetration analysis in porous media is of great importance in a wide range of applications such as ink jet printing technology, painting and textile design. This article presents an investigation of droplet impingement onto metallic meshes, aiming to provide insights by identifying and quantifying impact characteristics that are difficult to measure experimentally. For this purpose, an enhanced Volume-Of-Fluid (VOF) numerical simulation framework is utilised, previously developed in the general context of the OpenFOAM CFD Toolbox. Droplet impacts on metallic meshes are performed both experimentally and numerically with satisfactory degree of agreement. From the experimental investigation three main outcomes are observed—deposition, partial imbibition, and penetration. The penetration into suspended meshes leads to spectacular multiple jetting below the mesh. A higher amount of liquid penetration is linked to higher impact velocity, lower viscosity and larger pore size dimension. An estimation of the liquid penetration is given in order to evaluate the impregnation properties of the meshes. From the parametric analysis it is shown that liquid viscosity affects the adhesion characteristics of the drops significantly, whereas droplet break-up after the impact is mostly controlled by surface tension. Additionally, wettability characteristics are found to play an important role in both liquid penetration and droplet break-up below the mesh.

16 July 2022 in Applied Thermal Engineering
Verified
Journal Article
Closed access
KVKonstantinos Vontas
Konstantinos Vontas
NMNicolas Miché
Nicolas Miché
Marco MarengoMarco Marengo
Marco Marengo
Anastasios GeorgoulasAnastasios Georgoulas
Anastasios Georgoulas

14 October 2021 in Energies
Verified
Journal Article
Open access
PDF file
KVKonstantinos Vontas
Konstantinos Vontas
Manolia AndredakiManolia Andredaki
Manolia Andredaki
Anastasios GeorgoulasAnastasios Georgoulas
Anastasios Georgoulas
NMNicolas D. D. Miché
Nicolas D. D. Miché
Marco MarengoMarco Marengo
Marco Marengo
Phase change heat transfer within microchannels is considered one of the most promising cooling methods for the efficient cooling of high-performance electronic devices. However, there are still fundamental parameters, such as the effect of channel hydraulic diameter Dh whose effects on fluid flow and heat transfer characteristics are not clearly defined yet. The objective of the present work is to numerically investigate the first transient flow boiling characteristics from the bubble inception up to the first stages of the flow boiling regime development, in rectangular microchannels of varying hydraulic diameters, utilising an enhanced custom VOF-based solver. The solver accounts for conjugate heat transfer effects, implemented in OpenFOAM and validated in the literature through experimental results and analytical solutions. The numerical study was conducted through two different sets of simulations. In the first set, flow boiling characteristics in four single microchannels of Dh = 50, 100, 150, and 200 μm with constant channel aspect ratio of 0.5 and length of 2.4 mm were examined. Due to the different Dh, the applied heat and mass flux values varied between 20 to 200 kW/m2 and 150 to 2400 kg/m2s, respectively. The results of the two-phase simulations were compared with the corresponding initial single-phase stage of the simulations, and an increase of up to 37.4% on the global Nu number Nuglob was revealed. In the second set of simulations, the effectiveness of having microchannel evaporators of single versus multiple parallel microchannels was investigated by performing and comparing simulations of a single rectangular microchannel with Dh of 200 μm and four-parallel rectangular microchannels, each having a hydraulic diameter Dh of 50 μm. By comparing the local time-averaged thermal resistance along the channels, it is found that the parallel microchannels configuration resulted in a 23.3% decrease in the average thermal resistance R¯l compared to the corresponding single-phase simulation stage, while the flow boiling process reduced the R¯l by only 5.4% for the single microchannel case. As for the developed flow regimes, churn and slug flow dominated, whereas liquid film evaporation and, for some cases, contact line evaporation were the main contributing flow boiling mechanisms.

6 September 2017
Verified
Conference Paper
Open access
PDF file
Anastasios GeorgoulasAnastasios Georgoulas
Anastasios Georgoulas
KVKonstantinos Vontas
Konstantinos Vontas
Manolia AndredakiManolia Andredaki
Manolia Andredaki
KNKonstantinos Stefanos Nikas
Konstantinos Stefanos Nikas
Marco MarengoMarco Marengo
Marco Marengo
The “Direct Numerical Simulations” (DNS) of droplet impact processes is of great interest and importance for a variety of industrial applications, where laboratory experiments might be difficult, costly and time-consuming. Furthermore, in most cases after validated against experimental data, they can be utilised to further explain the experimental measurements or to extend the experimental runs by performing “virtual” numerical experiments. In such “DNS” calculations of the dynamic topology of the interface between the liquid and gas phase, the selected dynamic contact angle treatment is a key parameter for the accurate prediction of the droplet dynamics. In the present paper, droplet impact phenomena on smooth, dry surfaces are simulated using three different contact angle treatments. For this purpose, an enhanced VOF-based model, that accounts for spurious currents reduction, which has been previously implemented in OpenFOAM CFD Toolbox, is utilised and further enhanced. Apart from the already implemented constant and dynamic contact angle treatments in OpenFOAM, the dynamic contact angle model of Kistler, that considers the maximum advancing and minimum receding contact angles, is implemented in the code. The enhanced VOF model predictions are initially compared with literature available experimental data of droplets impacting on smooth surfaces with various wettability characteristics. The constant contact angle treatment of OpenFOAM as well as the Kistler’s implementation show good qualitative and quantitative agreement with experimental results up to the point of maximum spreading, when the spreading is inertia dominated. However, only Kistler’s model succeeds to accurately predict both the advancing and the recoiling phase of the droplet impact, for a variety of surface wettability characteristics. The dynamic contact angle treatment fails to predict almost all stages of the droplet impact. The optimum version of the model is then applied for 2 additional series of parametric numerical simulations that identify and quantify the effects of surface tensionand viscosity, in the droplet impact dynamics.DOI: http://dx.doi.org/10.4995/ILASS2017.2017.5020

27 June 2023 in Energies
Verified
Journal Article
Open access
PDF file
KVKonstantinos Vontas
Konstantinos Vontas
MPMarco Pavarani
Marco Pavarani
NMNicolas D. D. Miché
Nicolas D. D. Miché
Marco MarengoMarco Marengo
Marco Marengo
Anastasios GeorgoulasAnastasios Georgoulas
Anastasios Georgoulas
Flow boiling within conventional, mini and micro-scale channels is encountered in a wide range of engineering applications such as nuclear reactors, steam engines and cooling of electronic devices. Due to the high complexity and importance of the boiling process, several numerical and experimental investigations have been conducted for the better understanding of the underpinned physics and heat transfer characteristics. One of the most widely used numerical approaches that can analyse such phenomena is the Eulerian–Eulerian two-fluid method in conjunction with the RPI model. However, according to the current state-of-the-art methods this modelling approach heavily relies on empirical closure relationships derived for conventional channels, limiting its applicability to mini- and micro-scale channels. The present paper aims to give further insights into the applicability of this modelling approach for non-conventional channels. For this purpose, a numerical investigation utilising the Eulerian–Eulerian two-fluid model and the RPI wall heat flux partitioning model in OpenFOAM 8.0 is conducted. Initially the parameters comprising the empirical closure relationships used in the RPI sub-models are tuned against the DEBORA experiments on conventional channels, through an extensive sensitivity analysis. In the second part of the investigation, numerical simulations against flow boiling experiments within micro-channels are performed, utilising the previously optimised and validated model setup. Furthermore the importance of including a bubble coalescence and break-up sub-model to capture parameters such as the radial velocity profiles, is also illustrated. However, when the optimal model setup, in conventional tubes, is used against micro-channel experiments, the need to develop new correlations from data obtained from mini and micro-scale channel studies, not from experimental data on conventional channels, is revealed.