We analyze the case of a building that collapsed in a multifamily complex of Tlalpan borough in Mexico City during the 19 September 2017 Central Mexico earthquake. Despite having similar materials and similar structural and geometric properties, this was the only building that collapsed in the complex. A structural analysis of the building and a study of the soils’ predominant periods indicated that resonance effects, if any, would not be significant. However, phenomena related to the anomalous performance of buildings in dense urban areas such as geological soil, soil–structure interaction, and soil–city interaction effects were also investigated. A detailed analysis of the directionality of seismic actions recorded at nearby accelerometric stations and of the azimuths of sound and damaged buildings indicates that directionality effects were responsible for the collapse of the building. Subsequently, a set of 58, two‐component acceleration records of the earthquake was used to perform a thorough directionality analysis. The results were then compared with the foreseen uniform hazard response spectra and the design spectra in the city. Seismic actions in the city due to this earthquake were stronger than those corresponding to the uniform hazard response spectra. In addition, although design spectra have been significantly improved in the new 2017 Mexican seismic regulations, they were exceeded in 11 of 58 analyzed spectra. In 4 of these 11 cases, the design spectra were exceeded due to directionality effects. These results confirm the necessity of considering directionality effects in damage assessments, strong‐motion prediction equations, and design regulations.

Recycling is an important habit to avoid waste. This paper evaluates the performance of masonry mortar, elaborated by replacing natural sand with recycled fine aggregate (RFA) obtained from mortar. Five families of mixtures were prepared with different replacement proportions: 20%, 40%, 60%, and 100%. A 1:4 volumetric cement-to-aggregate ratio was used for all mixtures by experimentally adjusting the amount of water to achieve the same consistency of 175 ± 5 mm. The effects of the following procedures were analyzed: (1) the use of a deconstruction technique to collect the RFA, (2) pre-wetting of the aggregates, and (3) the use of a commercial plasticizer. Experimental results show that it is possible to use this type of recycled fine aggregate as a substitute for natural sand by up to 60% in the manufacture of masonry mortar without significantly affecting its properties.

Most of buildings and structures are usually projected according to two main axes. However, the geographical position of these buildings varies randomly. Such random distributions of the azimuthal positions of structures, in most of the cities, generally, are not accounted for when assessing their seismic risk; certainly, the direction of the seismic loads is another highly random variable. Moreover, an additional important source of uncertainty is related to the structural response, mainly due to the random character of the mechanical properties. There is a consensus that uncertainties must be considered for adequately assessing the seismic risk of structures, but these directionality effects have not been deeply explored so far. In this article, the influence of the high uncertainty involved in these input variables on the expected seismic damage is analysed. Thus, an actual earthquake, which affected the southern part of Spain, is studied. Notably, damages on a group of affected buildings, located close to the epicentre, are analysed and discussed in detail. The results show that the influence of the random azimuthal position of structures is an important source of uncertainty and that it should be taken into account when estimating the expected seismic risk in urban areas.

Recent research have proven the importance of considering the directionality effect on the expected seismic damage of structures. However, it demands a high computational effort if the nonlinear dynamic analysis (NLDA) is used to estimate the seismic response. This paper presents a simplified approach to obtain peak response parameters for a building subjected to bi-directional ground motions considering the directionality effect. To do so, the maximum and median response spectra, considering all the non-redundant response spectra, of several ground motion pairs are calculated. Afterwards, a spectral matching technique is applied to these spectra and new acceleration components are obtained. A series of NLDA are performed with these new components and the roof displacement and base shear values are calculated. These results are compared with the maximum and median values, calculated by performing a series of NLDA, after rotating the earthquakes records by considering increments of 1° in the interval 0°–180°. The results agree with both approaches validating the efficiency of the simplified proposed approach.