Alessandro Acquaviva

Mr. Alessandro Acquaviva

Chalmers University of Technology
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 April 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
AAAlessandro Acquaviva
Alessandro Acquaviva
SSStefan Skoog
Stefan Skoog
TTTorbjörn Thiringer
Torbjörn Thiringer
Tooth coil windings, in particular when using a double layer structure, present opportunities for in-slot liquid cooling. Since the windings are not overlapping, access to the slot from the end section for coolant liquids is enabled. In this paper, a solution for in-slot and in-stator direct oil cooling for a tooth coil winding machine is presented. The coils are pre-wound on bobbins and inserted on the stator teeth. The novelty of the design consists in the integration of the cooling, using a thermally conductive epoxy resin to create the channels within the slot as well as the positioning of the stator yoke cooling channels. A 50 kW machine for an automotive traction ap-plication is designed, manufactured and tested. Conjugate heat transfer simulations are used in the design process in combination with finite element analysis for the loss mapping. The thermal model is verified with measurements at 6 l/min oil flow and 17.5 A/mm $^{2}$ continuous and 35 A/mm $^{2}$ 30 s peak. The thermal model is then used to establish a continuous operating point of 25 A/mm $^{2}$ .

25 June 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Open access
AAAlessandro Acquaviva
Alessandro Acquaviva
ARArtem Rodionov
Artem Rodionov
AKAnton Kersten
Anton Kersten
TTTorbjörn Thiringer
Torbjörn Thiringer
YLYujing Liu
Yujing Liu
The reverse conduction capability of MOSFETs is beneficial for the efficiency of a three-phase inverter. In this paper analytical expressions in closed form are presented which allow to quickly evaluate the conduction losses, considering the effect of the reverse conduction and blanking time for both sinusoidal PWM operation with and without third harmonic injection. The losses of a three-phase SiC MOSFET inverter suitable for traction applications are estimated with the proposed method and show good agreement of about 98.5 % with measurements, performed with a calorimetric setup.

19 August 2019 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
AAAlessandro Acquaviva
Alessandro Acquaviva
OWOskar Wallmark
Oskar Wallmark
EGEmma Arfa Grunditz
Emma Arfa Grunditz
SLSonja Lundmark
Sonja Lundmark
TTTorbjörn Thiringer
Torbjörn Thiringer
Modeling of electrical machines is a multiphysics problem. Depending on the phenomena of interest and the computational time constraint, this can be done at different levels of detail. In this paper, the main approaches to model the thermal behaviour of electrical machines with a liquid cooled casing around the stator (often referred to as cooling jacket) are analyzed and a novel approach is presented. The proposed method aims at creating computationally efficient 3D multi-physics models of electrical machines with liquid cooled jacket. This model is based on the assumption of a fully developed flow in the cooling jacket which allows to scale the CFD simulation to 1D. The slot with a two layer concentrated winding and potting material is modeled using a composite material comprising of both the conductors and slot filler. Similarly, a unified material is used to model the end-windings. Experimental results on a traction machine for vehicle applications are presented showing good agreement with the simulations. Also, a comparison with a 3D CFD is presented to verify the pressure drop in the pipe bend. Finally, the model is used to simulate a dynamic load cycle, which would be computationally extremely demanding with combined 3D CFD and thermal FEA of the machine and its cooling.

30 June 2020 in Energies
Verified
Journal Article
Open access
PDF file
AAAlessandro Acquaviva
Alessandro Acquaviva
SSStefan Skoog
Stefan Skoog
EGEmma Grunditz
Emma Grunditz
TTTorbjörn Thiringer
Torbjörn Thiringer
Tooth coil winding machines offer a low cost manufacturing process, high efficiency and high power density, making these attractive for traction applications. Using direct oil cooling in combination with tooth coil windings is an effective way of reaching higher power densities compared to an external cooling jacket. In this paper, the validation of the electromagnetic design for an automotive 600 V, 50 kW tooth coil winding traction machine is presented. The design process is a combination of an analytical sizing process and FEA optimization. It is shown that removing iron in the stator yoke for cooling channels does not affect electromagnetic performance significantly. In a previous publication, the machine is shown to be thermally capable of 25 A/mm 2 (105 Nm) continuously, and 35 A/mm 2 (140 Nm) during a 10 s peak with 6 l/min oil cooling. In this paper, inductance, torque and back EMF are measured and compared with FEA results showing very good agreement with the numerical design. Furthermore, the efficiency of the machine is validated by direct loss measurements, using a custom built calorimetric set-up in six operating points with an agreement within 0.9 units of percent between FEA and measured results.