zhi tang

Prof. zhi tang

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 March 2024 in Processes
Verified
Journal Article
Open access
PDF file
ZTzhi tang
zhi tang
ZWZhiwei WU
Zhiwei WU
DJDunwei Jia
Dunwei Jia
JLJinGuo LV
JinGuo LV
The distribution law of the ground stress field is of great significance in guiding the design of coal mine roadway alignment, determining the parameters of roadway support, and preventing and controlling the impact of ground pressure in coal mines. A geostress inversion method combining Rhino surface modeling and FLAC3D 6.0 numerical simulation software is proposed. Based on the geological data of the coal mine and the results of on-site measurements, a three-dimensional geological model of Yingcheng Coal Mine is established for the geostress inversion, and the distribution law of the geostress field in Yingcheng Coal Mine is obtained. Research shows the following: (1) The horizontal maximum principal stress values of the Yingcheng Mine are between 33.9 and 35.3 MPa, the horizontal minimum principal stress values are between 23.6 and 25.4 MPa, and the direction of the horizontal maximum principal stress is roughly in the southwest to west direction; (2) the three-way principal stress magnitude relationship is σH > σv > σh, indicating that the horizontal stress dominates in the study area, which belongs to the slip-type stress state; (3) The maximum principal stress of No. 3 coal seam is 33.1–34.8 MPa, the middle principal stress is 27.5–29.2 MPa, and the minimum principal stress is 17.3–22.9 MPa. Due to the influence of topography and burial depth, there is a phenomenon of stress concentration in some areas. By comparing the inversion values with the measured values, the accuracy of the geostress inversion is high, and the initial geostress inversion method based on Rhino surface modeling accurately inverts the geostress distribution pattern of the Yingcheng coal mine.

8 January 2021 in Complexity
Verified
Journal Article
Open access
PDF file
ZTzhi tang
zhi tang
HWHao Wu
Hao Wu
JLJinguo Lv
Jinguo Lv
ZXZhuangzhuang Xin
Zhuangzhuang Xin
WZWenbo Zuo
Wenbo Zuo
In order to improve the impact resistance and mechanical performance of anchor rods and satisfy the requirements for supporting rockburst roadways, the energy balance equation of the energy‐absorbing support and roadway surrounding rock system is established. Moreover, to effectively prevent rockburst disasters, the energy criterion for roadway instability is derived. From the perspective of an energy‐absorbing support, a yield‐absorbing anti‐shock anchor composed of a rod body, tray, constant resistance energy‐absorbing device, and special‐shaped nut is designed and developed; compared with ordinary anchor rods, this rod has stronger mechanical properties for resisting impact. Theoretical and numerical simulation studies show that the energy‐absorbing device has a repeatable deformation failure mode and a constant yield force. The paper also presents the principle involved in the design of anti‐shock bolt supports. The energy‐absorbing support not only effectively guides and controls the release and conversion of impact energy but also consumes the impact energy in the buffering process of the anchor to ensure the stability of surrounding rock and support protection system. This study aims to provide reference for roadway support design and to improve rock bolts used in rockburst roadways.

11 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
ZTzhi tang
zhi tang
HWHao Wu
Hao Wu
YLYing Liu
Ying Liu
YPYishan Pan
Yishan Pan
JLJinGuo LV
JinGuo LV
DCDezhi Chang
Dezhi Chang
In order to improve the impact resistance mechanical properties of bolt, the requirements of rock burst roadway support must be met. Based on the requirements that the anchor should have a reasonable deformation load threshold, high stroke efficiency, constant reaction force and stable repeatable deformation damage mode. A constant resistance anti-impact device was designed, and a new constant resistance energy-absorbing impact anchor rod was designed in combination with a conventional anchor rod, and the working principle of a constant resistance energy-absorbing impact anchor rod was given. ABAQUS finite element software was used to analyze the mechanical properties of bolt and the results showed that the constant resistance energy-absorbing anti-shock anchor has a stable and repeatable deformation damage mode under both static and impact loads, and the three indexes of the constant resistance energy-absorbing anti-shock anchor, such as yield distance, impact resistance time and energy absorption, are significantly better than those of the conventional anchor. The impact energy and impact velocity have less influence on the load-bearing capacity and stroke efficiency of the impact device. The impact velocity has less influence on the indices of the rod yield load, breaking load, absorbed energy and the yield distance of a conventional anchor and constant resistance energy-absorbing anti-stroke anchor, and the impact resistance time decreases non-linearly with the increase in the impact velocity.

2 March 2023 in Frontiers in Earth Science
Verified
Journal Article
Open access
ZTzhi tang
zhi tang
WZWenbo Zuo
Wenbo Zuo
KGKe Gao
Ke Gao
XCXiaoqiao Cai
Xiaoqiao Cai
A mechanical model of a circular section of a tunnel roadway considering damage is established to improve the impact protection performance of the “roadway rock-support” system and provide a theoretical basis for designing coal mine impact ground pressure roadway support. The formula of the critical rock burst load of a circular roadway is derived according to the instability theory of rock burst disturbance response. The influence of mechanical properties of surrounding rock and roadway support strength on the critical rock burst load of a roadway rock-support system is studied using the control variable method. The research shows that 1) under the support condition of a roadway, with the increase of uniaxial compressive strength, softening modulus, and internal friction angle of surrounding rock, the critical rock burst load of a roadway has an increasing trend; the critical rock burst load of roadway decreases with the increase of the elastic modulus of the surrounding rock. 2) Under the condition of no support, with the increase of uniaxial compressive strength, elastic modulus, and internal friction angle of surrounding rock, the critical rock burst load of roadway tends to increase. With the decrease of the surrounding rock’s softening modulus, the critical rock burst load of the roadway decreases. When the aforementioned four kinds of surrounding rock influence factors are the same, the critical load of rock burst under the supporting condition is much larger than that under the non-supporting condition. 3) A new impact tendency index K is defined as the ratio of the softening modulus and the elastic modulus. 4) The critical load of rock burst increases approximately linearly with the increase of support stress. The critical load of a rock burst is about 400 times as large as the supporting stress. Increasing roadway support strength can greatly improve the stability of the supporting and roadway surrounding rock system, and the stability of the supporting and roadway surrounding rock system can be improved by reasonably changing the mechanical properties of the surrounding rock.

9 April 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
JLJinGuo LV
JinGuo LV
JLJinguo Lyu
Jinguo Lyu
YPYishan Pan
Yishan Pan
ZTzhi tang
zhi tang
Monitoring and preventing coal–rock dynamic disasters are essential for ensuring sustainable and safe mining. Induced charge monitoring, as a geophysical method, enables sustainable monitoring of coal–rock deformation and failure. The induced charge signal contains crucial information regarding damage evolution, making it imperative and important to explore its temporal characteristics for effective monitoring and early warnings of dynamic disasters in deep mining. This paper conducted induced charge monitoring tests at different loading rates, investigating the multifractal characteristics of induced charge signals during the early and late stages of loading. It proposed the maximum generalized dimension D(q)max, multifractal spectrum width Δα, and height difference Δf as multifractal parameters for induced charge signals. Additionally, quantitative characterization of coal damage was performed, studying the variation patterns of signal multifractal characteristic parameters with coal damage evolution. This study revealed the induced charge signal of the coal body multifractal characteristics in the whole loading process. In the late loading stage, the double logarithmic curve demonstrated some nonlinearity compared to the previous period, indicating the higher non-uniformity of the induced charge time series. D(q)max and Δα in the late loading stage were higher than those in the early stage and increased with loading rates. As coal damage progressed, there were significant jumps of D(q)max in both the early and late stages of damage, with larger jumps indicating richer fracture events in the coal. The width Δα showed an overall trend of increase–decrease–increase with coal damage evolution, while the height difference Δf fluctuated around zero in the early stage of damage development but increased significantly during severe damage and destruction. By studying the multifractal characteristics of induced charge signals, this study provides insights for the early identification of coal–rock dynamic disasters.

16 April 2022 in Geofluids
Verified
Journal Article
Open access
BJBaoxin Jia
Baoxin Jia
HCHAO CHEN
HAO CHEN
ZLZhiyong Li
Zhiyong Li
ZTzhi tang
zhi tang
Overlying Rock Activity Laws and Influential Ranges of Coal Seam Mining in Stubble Areas: This report applies theoretical analysis, similar material simulations, and numerical simulation methods to study the overburden strata movements and influential range of coal mining under pressure stubble conditions and to elucidate the relationship between adjacent coal seams. The pressure, failure, caving, stress, and displacement of crop conditions during coal seam mining were evaluated. The results show that the overlying W9-10 coal face and underlying J16-17 roof experience a long first pressure step, i.e., close to the periodic weighting distance. The working face of the W9-10 coal seam is located in the bending subsidence zone of the working face of the J16-17 coal seam. With the advance of the working face of the J16-17 coal seam, the development and range of overburden fracture of the W9-10 coal seam gradually increase. The supporting pressure and displacement caused by the mining process at the W coal seam have no impact on the coal seam of the stubble area, whereas the mining of the J coal seam leads to a continuous increase in the overburden displacement of the W coal seam; the latter also induces a shift in the maximum displacement to the rear, which is more significant for the stress concentration at the middle and front regions of the stubble area, thus presenting a superposition effect. The stress caused by mining at the coal seam decreases with increasing vertical distance from the roof or floor. For distant coal seams, the main contributing factor is the effect of vertical stress. The influential range of the vertical stress caused by mining in the overlying working face remains within 90m, whereas the influential range of the stress caused by mining in the underlying working face is relatively large, i.e., it still affects the roadway at distances up to 160m. The results and discussion presented herein provide significant practical value in terms of understanding the overburden strata activity and its influential range in adjacent mines stubble areas, which can be used to guide group mining efforts.