During the last few decades, unheated attic spaces (so-called “cold attics”) have been one of the most moisture-problematic spaces in the building practices of Europe and North America. Problems with such spaces are usually associated with condensation, frost formation, and mould growth on the lower surfaces of the roof deck. To solve these problems, a number of qualitative studies were performed. Although these studies revealed many important pieces of information, some of them are seemingly not in accordance with one another. Therefore, there has not yet been presented cold attic design which is suitable (especially moisture-safe) for the whole target region. The aim of this paper is to determine whether such a design can be determined or state the reasons why it is not possible. Based on a review of published studies, 38 cold attic designs were selected for detailed analysis. Their comparative parameters were established, quantified, and compared. The moisture-safeness of each design was evaluated using an original approach, and the designs were sorted into groups based on their similarities. Despite many uncertainties, it was found that the criteria for moisture-safe cold attic design in the target region can likely be stated.
The possible influence of anatomical sections of wood on mold growth was investigated by means of a laboratory experiment. The selected fungi, Aspergillus sp., Penicillium sp., and Alternaria sp. were inoculated by spraying on the surface of wood specimens prepared from pine (Pinus sylvestris) and spruce (Picea abies). The incubation was carried out under stable environmental conditions (temperature of 22 °C, relative humidity of 75, 87, and 95%) over three months. Mold growth was evaluated based on regular microscopic and macroscopic observations. The recorded mold coverage fractions and the qualitative indicators of mold development were later expressed by a dimensionless mold index. The differences in mold growth in the anatomical sections of wood were found to be relatively insignificant. In contrast, comparison of measured data with other experimental studies showed large differences, especially in the initial growth phase. The discrepancy is probably related to differences among the experimental protocols. It is concluded that laboratory mold growth studies would be improved if a common standardized methodology was developed and followed.
Clay and earthen materials are highly hygroscopic and thus able to effectively adsorb and release moisture from their surroundings. This paper analyses the ability of rammed earth to stabilize internal course of relative humidity. A numerical hygrothermal model is introduced and validated using a set of measured data according to IEA Annex 41. The model is then used to determine the stabilization effect of rammed earth in a residential room with defined moisture sources and ventilation rate. The simulation is performed for gypsum boards, concrete and red brick as well and a clear comparison is made. The results show that the rammed earth can most effectively moderate the indoor air humidity variations; followed by concrete, gypsum boards, and red brick.
This paper deals with mathematical modeling of mold growth on wood. The logistic growth equation is used to model mold growth phenomena in changing environmental conditions. Microscopic mold coverage fraction is used in the logistic equation to represent mold development on a material surface over time. The current state-of-the-art dynamic Finnish mold growth model is used as the reference model for development of the logistic mold growth model. The optimal values of mold growth coefficient are estimated by simulations of mold growth under constant environmental conditions and by finding the best agreement with the Finnish mold growth model using mathematical optimization methods. It is shown that the mold growth coefficient can be approximated as a function of relative humidity, temperature, wood species and the quality of the surface. The model parameters are then verified by a comparison with the Finnish mold growth model. In this case, cyclic step changes of constant relative humidity are used. Finally, the logistic mold growth model is compared with published experimental observations of mold growth. The discrepancy of mold growth models and experimental mold growth data, and possible improvements are discussed.
The moisture behaviour of wood has been naturally studied since ancient times. Despite being commonly used in almost all industries, some of its moisture proper
1 December 2023 in Journal of Physics: Conference Series
The determination of water vapor transmission properties is commonly performed using the cup method. The method is based on periodic weighing of the cup assembly over time. If the air density surrounding the balance differs between weighings, measured change of mass is affected by the difference of ambient air buoyant force. For the correction of this effect can be used a mathematical formula presented in the literature and standards. The ASTM E96 states that this correction is important if observing changes of water vapor mass 0–100 mg. This paper therefore analyses possible errors of measured water vapor transmission properties based on a single 100 mg mass change without applying the buoyancy correction. It was found that for most common samples of building materials (sd < 3 m) and regular sizes of cup assemblies the error of a single mass change measurement can be up to ca. ±13 %, while assemblies with higher volume, higher mass, or more vapor tight samples can experience an error up to ±26 %. However, the vapor transmission properties are usually determined based on five consecutive weight changes. In that case the error can be up to five times lower (±2.5–5 %). Regarding the formula of the buoyancy correction the most important parameter was found to be the chosen volume of the cup assembly which, however, depends on particular setup and sample air-permeance. Only two extreme scenarios regarding this topic were analyzed while the full understanding of the accurate correction is still unsolved in its complexity.