Compositionally layered BaxSr1−xTiO3 (Ba0.60Sr0.40TiO3–Ba0.75Sr0.25TiO3–Ba0.90Sr0.10TiO3) 220nm thin film heterostructures were fabricated on Pt coated high resistivity Si substrates via the metal organic solution deposition technique (MOSD). Optimization of the material design was achieved by evaluating two integration schemes, namely, the single- and multianneal process protocols. Materials characterization demonstrated that both film process protocols resulted in smooth, dense, crack-free films with a single phase perovskite structure. Rutherford backscattering spectroscopy revealed compositionally distinct layers and severe elemental interdiffusion for the films fabricated via the multianneal and single-anneal process protocols, respectively. The retention of the compositional layering subsequent to film crystallization deemed the multianneal processed BaxSr1−xTiO3 (BST) film suitable for evaluation of dielectric properties. The dielectric properties were compared to both paraelectric uniform composition BST and to the relevant compositionally graded BST films reported in the technical literature. Our results made evident that the multiannealed compositionally layered BST films possessed higher permittivity (εr=360) and lower dissipation factor (tanδ=0.012) with respect to both uniform composition paraelectric Ba0.60Sr0.40TiO3 film fabricated via the same MOSD processing method and the relevant literature values for compositionally graded BST films. The multilayered BST material design exhibited minimal dielectric dispersion in the range of 90to−10°C, showing a 6.4% decrease in permittivity (corresponding to a temperature coefficient of capacitance TCC20–90=−0.921) as the temperature was elevated from 20to90°C and only a 2.1 increase in permittivity (TCC20–(−10)=−0.716) as the temperature was lowered from 20to−10°C. Additionally, the dielectric tunability of the multilayered BST structures over the temperature range of −10–90°C was temperature independent. Our results show that the multilayered BST design has excellent dielectric properties and the enhanced tunability and dielectric loss are stable over a relatively broad temperature range (−10–90°C), thereby making them excellent candidates for the next generation of enhanced performance temperature stable tunable devices.
We have grown 5mol% MgO-doped multilayered Ba1−xSrxTiO3 (BST) films having a nominal thickness of 220nm with compositions of each layer as BST60/40, BST75/25, and BST90/10 (upgraded). We also fabricated undoped upgraded BST and uniform BST60/40 films for comparison. Results show that Mg-doping improves dielectric loss (tanδ=0.008) and yields better surface roughness (∼3.1nm) compared to undoped upgraded BST. Mg-doped films displayed excellent temperature stability with temperature coefficient of capacitances of −0.94 and 1.14ppt∕°C from 20to90°C and 20to−10°C, respectively. Mg doping resulted in a moderate dielectric tunability (29%) compared to undoped BST (65.5%) at 444kV∕cm.
Pt/Ti/WSi/Ni ohmic contacts to n-SiC, initially annealed at 950 and for 30 s, were evaluated for thermal stability via pulsed/cyclic thermal fatigue and aging experiments at Modifications of material properties in response to cyclic thermal fatigue and aging tests were quantitatively assessed via current–voltage measurements, field emission scanning microscopy, atomic force microscopy, and Rutherford backscattering spectrometry. Negligible changes in the electrical properties, microstructure, and surface morphology/roughness were observed for both annealed ohmic contacts in response to 100 cycles of acute cyclic thermal fatigue. Aging of the annealed contact for 75 h at resulted in electrical failure and chemical interdiffusion/reaction between the contact and SiC substrate. The annealed contact retained ohmicity after 100 h of aging and was found to be chemically and microstructurally stable. These findings indicate that the annealed Pt/Ti/WSi/Ni ohmic contact to n-SiC is thermally stable and merits strong potential for utilization in high temperature and pulsed power devices.
The dielectric properties of barium strontium titanate thin films with composition Ba0.6Sr0.4TiO3 were studied as a function of film thickness for implementation in a variety of devices with different requirements. Films were prepared by metalorganic solution deposition and characterized using scanning electron microscopy, atomic force microscopy, and Rutherford back-scattering. The dielectric (100 kHz) and insulating properties were also measured. The film morphology and dielectric/insulating properties are thickness dependent, yet the best combination of properties was in films of 160 nm to 240 nm. These films had a moderate dielectric constant (∼300), low loss (∼ 0.029), good tunability (∼ 30%), and low leakage current (∼ 10− 8 A/cm2).