Ryan Toonen

Prof. Ryan Toonen

orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2009 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
RTRyan Toonen
Ryan Toonen
SBSamuel P. Benz
Samuel P. Benz
We have extended the application of quantum-based electrical standards from single frequency calibrations to multi-tone tests that can be used to characterize the nonlinear behavior of electronic components and circuits. Specifically, we have used a Josephson arbitrary waveform synthesizer to generate highly accurate, two-tone waveforms having center frequencies ranging from 10 kHz to 1 MHz. These waveforms have unprecedented spectral purity because they are constructed from perfectly quantized voltage pulses. Using this measurement system, we have characterized the intermodulation distortion properties of a highly linear amplifier used in metrological applications. Additionally, we have shown that these test signals can be upconverted to microwave frequencies, so that they may be used to characterize the nonlinearities of RF and microwave components.

1 October 2009 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
CWC. V. Weiss
C. V. Weiss
MOM. B. Okatan
M. B. Okatan
SAS. P. Alpay
S. P. Alpay
MCM. W. Cole
M. W. Cole
ENE. Ngo
E. Ngo
RTRyan Toonen
Ryan Toonen

15 December 2011 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
MCM. W. Cole
M. W. Cole
RTRyan Toonen
Ryan Toonen
MIM. Ivill
M. Ivill
SHS. G. Hirsch
S. G. Hirsch
ENE. Ngo
E. Ngo
CHC. Hubbard
C. Hubbard
Isothermal (700 °C) ultraviolet annealing (UVA) processing of crystallized Ba0.60Sr0.40TiO3 (BST) thin films for exposure times up to 225 min films has been studied. The BST films, grown on PtSi wafers via the metalorganic solution deposition (MOSD) technique, were crystallized via conventional furnace annealing (CFA) prior to UVA treatment, and the effects of UV annealing time on the structural, dielectric, and insulation properties were evaluated. The experimental results demonstrated significantly improved structural, dielectric, and insulation properties for the UVA films. Specifically, lattice parameter contraction (toward that of bulk BST60/40) and a 20% reduction in loss were observed for the UVA treated films with respect to the CFA/control film. Leakage current characteristics were found to be the most sensitive characterization technique to access material property modification as a result of UVA exposure time. Specifically, the 225 min UVA exposure time resulted in a three-order of magnitude reduction in leakage current density compared to the CFA film, and the lowest value observed was 1.06 × 10−7 A/cm2 at E = 300 kV/cm. The useable tunability (tunability value at the maximum acceptable leakage current, 500 pA) was found to be elevated by a factor of two with respect to that of the CFA/control BST film (52.31%/UVA film vs. 18.5%/control film). It is suggested that the improved material properties are due to the mitigation of unwanted oxygen vacancies within the film after UV-annealing. A mechanistic model is presented and discussed.

29 November 2005 in New Journal of Physics
Verified
Journal Article
Open access
PDF file
HQH Qin
H Qin
NSN Shaji
N Shaji
NMN E Merrill
N E Merrill
HKH S Kim
H S Kim
RTRyan Toonen
Ryan Toonen
GCG Celler
G Celler
We report the formation of micrometre-sized SiGe/Si tubes by releasing strained SiGe/Si bilayers from substrates in a wet chemical-etching process. In order to explore statistical studies of dynamic formation of microtubes, we fabricated arrays of square bilayers. Due to the dynamic change in curvature of the bilayers, and hence the underlying etch channels, the etching process deviates from a transport-controlled regime to one of kinetic controlled. We identified two distinct modes of etching. A slow etching mode is associated with symmetric surface deformation in which the bilayers mostly retain their initial pattern. In the fast mode, bilayers are asymmetrically deformed while large etch channels are induced and etching becomes kinetically controlled. Etch rate dispersion is directly related to the degree of asymmetry in surface deformation. When the dimensions of the bilayers become significantly larger than the curvature radius, kinetic etching dominates. During the formation of tubes, SiGe/Si bilayers strongly interact with the liquid environment of etchant and solvent. Assisted by the surface tension of evaporating liquids, the tubes are drawn near the substrate and eventually fixed to it because of van der Waals forces. Our study illuminates the dynamic etching and curling processes involved with and provides insight on how a uniform etch rate and consistent curling directions can be maintained.

26 September 2016 in Multidimensional Systems and Signal Processing
Verified
Journal Article
Closed access
PDF file
RRRobert R. Romanofsky
Robert R. Romanofsky
RTRyan Toonen
Ryan Toonen

9 December 2008 in Integrated Ferroelectrics
Verified
Journal Article
Closed access
CWC. V. Weiss
C. V. Weiss
MCMelanie Cole
Melanie Cole
SAS. P. Alpay
S. P. Alpay
ENE. Ngo
E. Ngo
RTRyan Toonen
Ryan Toonen
CHC. Hubbard
C. Hubbard
The dielectric properties of barium strontium titanate thin films with composition Ba0.6Sr0.4TiO3 were studied as a function of film thickness for implementation in a variety of devices with different requirements. Films were prepared by metalorganic solution deposition and characterized using scanning electron microscopy, atomic force microscopy, and Rutherford back-scattering. The dielectric (100 kHz) and insulating properties were also measured. The film morphology and dielectric/insulating properties are thickness dependent, yet the best combination of properties was in films of 160 nm to 240 nm. These films had a moderate dielectric constant (∼300), low loss (∼ 0.029), good tunability (∼ 30%), and low leakage current (∼ 10− 8 A/cm2).