Hurrem Akbıyık

Dr. Hurrem Akbıyık


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

14 October 2022 in Ocean Engineering
Verified
Journal Article
Closed access
MSMehmet Seyhan
Mehmet Seyhan
HAHurrem Akbıyık
Hurrem Akbıyık
MSMustafa Sarıoğlu
Mustafa Sarıoğlu
SKSevda Ceren Keçecioğlu
Sevda Ceren Keçecioğlu

29 September 2017 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
HAHurrem Akbıyık
Hurrem Akbıyık
HYHakan Yavuz
Hakan Yavuz
YAYahya Erkan Akansu
Yahya Erkan Akansu
In this paper, linear and spanwise-segmented plasma actuator implementations as well as base airfoil with no plasma cases are presented. These approaches are used to control the flow around a NACA0015 airfoil. The experiments were conducted in a wind tunnel at Reynolds number of 3.6×104. The plasma actuators mounted on the leading edge of the airfoil at chord position of 0.1 (x/C). The electrical parameters used for the plasma generating device are set to constant values of 6-kVpp applied voltage and 3.5-kHz excitation frequency. It is observed that the use of spanwise-segmented plasma actuators converts the 2-D flow structure around the airfoil into 3-D forcing flow structure. The change of the wake region width of the airfoil is visualized by using the smoke-wire method. The flow visualization is performed at attack angles of 0°, 5°, 10°, and 15°. In addition, necessary measurements are also made to determine drag and lift forces. A comparative study on the drag and lift forces for the NACA0015 airfoil is performed. As a part of the conclusions, linear and spanwise-segmented plasma actuator implementations as well as base airfoil with no plasma cases are compared and related results on flow control are presented.

1 September 2025 in Physics of Fluids
Verified
Journal Article
Closed access
FKFatih Kaya
Fatih Kaya
HAHurrem Akbıyık
Hurrem Akbıyık
An experimental study was conducted to investigate the aerodynamic characteristics and surface flow topologies of spiky-vortex generators (Spiky-VGs) placed on the National Advisory Committee for Aeronautics (NACA0012) airfoil. Within the scope of this study, aerodynamic force measurement and titanium-dioxide (TiO2) surface oil experiments were performed at a Reynolds number (Re) of 1.5 × 105. Moreover, TiO2 surface oil and three-dimensional (3D) smoke-wire flow visualization techniques were applied to Spiky-VG having a certain scale. According to the aerodynamic force measurement results, it was observed that model 1 (M1) Spiky-VGs increase the maximum lift coefficient (CLmax) by 7.6% compared to the base NACA 0012 airfoil. It was observed that model 2 (M2) increased the lift coefficient (CL) by 9.9% at an angle of attack slightly above the stall angle of the baseline airfoil (α = 11°) and delayed the onset of stall by approximately 1°. Furthermore, the drag coefficient (CD) of model 2 (M2) is lower than that of the base wing model and is about 14.5%, indicating improved aerodynamic performance. It was observed that the presence of Spiky-VGs leads to significant alterations in surface flow topology over the wing model, primarily owing to their geometric configuration. The findings demonstrate that Spiky-VGs, functioning as vortex generators, contribute to enhanced aerodynamic performance by modifying surface flow topology and improving flow characteristics. Hence, they can be considered as effective passive flow control devices for airfoil applications.

7 January 2025 in Bioinspiration & Biomimetics
Verified
Journal Article
Closed access
FKFatih Kaya
Fatih Kaya
HAHurrem Akbıyık
Hurrem Akbıyık
An experimental study was carried out to investigate the effects of biomimetic vortex generators (biomimetic-VGs) on the aerodynamic performance of the NACA0015 airfoil. Aerodynamic force measurements and titanium dioxide (TiO2) based flow visualization technique experiments were performed for test models at Re = 1.2 × 105. Aerodynamic force measurement experiments were carried out in the wind tunnel at angles of attack of 0°–18° with an increment of 1°. As a result of the experiments, it was revealed that the lift coefficient (C L) increased and the drag coefficient (C D) decreased by using the seaconchshell structure as a VG for the wing model. In addition, it has been observed that biomimetic models (BMs) shifted the stall angle of the airfoil by 1°. In the surface oil flow visualization experiment results, the flow structure around the NACA0015 airfoil of BMs was revealed and interpreted. Moreover, it has been revealed that the aerodynamic performance of the airfoil increases as a result of the use of BMs. It is also revealed that the seaconchshell structure, which has not been studied before in the literature and which is the subject of this study, can be used as an effective flow control device.

1 April 2025 in Physics of Fluids
Verified
Journal Article
Closed access
HAHurrem Akbıyık
Hurrem Akbıyık
An experimental investigation was conducted to elucidate the effect of modified stepped region on a National Advisory Committee for Aeronautics (NACA) model NACA0012 airfoil surface at Reynolds number (Re) of 1×105. Force measurements as well as titanium dioxide (TiO2)-based flow visualization experiments and velocity measurements were carried out to evaluate aerodynamic performance change, to gain insight into flow structures, and to show the changes in wake region. The angle of attack (α) of the airfoil was chosen to lie between 0° and 30° with 1° intervals for force measurements. The attack angles were chosen as 0°, 6°, and 12° considering pre-stall and post-stall cases for velocity measurements and surface oil visualization. In the light of force measurement experiments, it was concluded that a fully step model and all modified models had a higher lift coefficient (CL) value than the base model (BM). It is observed that the D2 model results in 13.22% improvement in the CL value at α=12° compared to the BM. The drag coefficient of the D3 model shows less increase compared to the other modified models, with a value about 0.113 at α=11°. However, there were no improvements in drag reduction when the base airfoil was modified. Velocity measurements showed that the effect of stepped modifications in the pressure surface provides the wake width changes and the wake width centerline shifts. TiO2-based surface oil visualizations were provided to enlighten the new flow structures as cavity-based induced flow structure, step-based induced flow structure, wavy shape reattachment line and wavy shape recirculation region.