Oil and gas extraction frequently produces substantial volumes of produced water, leading to several mechanical and environmental issues. Several methods have been applied over decades, including chemical processes such as in-situ crosslinked polymer gel and preformed particle gel, which are the most effective nowadays. This study developed a green and biodegradable PPG made of PAM and chitosan as a blocking agent for water shutoff, which will contribute to combating the toxicity of several commercially used PPGs. The applicability of chitosan to act as a crosslinker has been confirmed by FTIR spectroscopy and observed by scanning electron microscopy. Extensive swelling capacity measurements and rheological experiments were performed to examine the optimal formulation of PAM/Cs based on several PAM and chitosan concentrations and the effects of typical reservoir conditions, such as salinity, temperature, and pH. The optimum concentrations of PAM with 0.5 wt% chitosan were between 5–9 wt%, while the optimum chitosan amount with 6.5 wt% PAM was in the 0.25–0.5 wt% range, as these concentrations can produce PPGs with high swellability and sufficient strength. The swelling capacity of PAM/Cs is lower in high saline water (HSW) with a TDS of 67.2976 g/L compared with fresh water, which is related to the osmotic pressure gradient between the swelling medium and the PPG. The swelling capacity in freshwater was up to 80.37 g/g, while it is 18.73 g/g in HSW. The storage moduli were higher in HSW than freshwater, with ranges of 1695–5000 Pa and 2053–5989 Pa, respectively. The storage modulus of PAM/Cs samples was higher in a neutral medium (pH = 6), where the fluctuation behavior in different pH conditions is related to electrostatic repulsions and hydrogen bond formation. The increase in swelling capacity caused by the progressive increment in temperature is associated with the amide group’s hydrolysis to carboxylate groups. The sizes of the swollen particles are controllable since they are designed to be 0.63–1.62 mm in DIW and 0.86–1.00 mm in HSW. PAM/Cs showed promising swelling and rheological characteristics while demonstrating long-term thermal and hydrolytic stability in high-temperature and high-salinity conditions.
Pharmaceutically active compounds (PhACs) represent an emerging class of contaminants. With a potential to negatively impact human health and the ecosystem, existence of pharmaceuticals in the aquatic systems is becoming a worrying concern. Antibiotics is a major class of PhACs and their existence in wastewater signifies a health risk on the long run. With the purpose of competently removing antibiotics from wastewater, cost-effective, and copiously available waste-derived adsorbents were structured. In this study, mango seeds kernel (MSK), both as a pristine biochar (Py–MSK) and as a nano-ceria-laden (Ce–Py–MSK) were applied for the remediation of rifampicin (RIFM) and tigecycline (TIGC). To save time and resources, adsorption experiments were managed using a multivariate-based scheme executing the fractional factorial design (FrFD). Percentage removal (%R) of both antibiotics was exploited in terms of four variables: pH, adsorbent dosage, initial drug concentration, and contact time. Preliminary experiments showed that Ce–Py–MSK has higher adsorption efficiency for both RIFM and TIGC compared to Py–MSK. The %R was 92.36% for RIFM compared to 90.13% for TIGC. With the purpose of comprehending the adsorption process, structural elucidation of both sorbents was performed using FT-IR, SEM, TEM, EDX, and XRD analyses which confirmed the decoration of the adsorbent surface with the nano-ceria. BET analysis revealed that Ce–Py–MSK has a higher surface area (33.83 m2/g) contrasted to the Py–MSK (24.72 m2/g). Isotherm parameters revealed that Freundlich model best fit Ce–Py–MSK–drug interactions. A maximum adsorption capacity (qm) of 102.25 and 49.28 mg/g was attained for RIFM and TIGC, respectively. Adsorption kinetics for both drugs conformed well with both pseudo-second order (PSO) and Elovich models. This study, therefore, has established the suitability of Ce–Py–MSK as a green, sustainable, cost-effective, selective, and efficient adsorbent for the treatment of pharmaceutical wastewater.
Crosslinkable polymers, such as polyacrylamide (PAM), are widely applied for water control in oil and gas reservoirs. Organic and inorganic crosslinkers are used to formulate a gel with PAM. Although chromium has a high level of toxicity, it has been implemented as an effective crosslinker combined with carboxylates because of the controllability of crosslinking time at low temperatures. The objective of this work was to develop greener d-metal inorganic crosslinkers based on cobalt, copper, and nickel to replace chromium for application at reservoir conditions. The obtained results showed that the gelation chemistry of the developed systems depends on the metal charge density. The gelation of PAM with d-metals depends on pH and temperature for low- and high-charge density, respectively. Cobalt (II) acetate (CoAc) was effective at high temperatures (130–150 °C) and forms (4% CoAc + 9%PAM) stable, and strong gels at a pH > 7 with a storage modulus exceeding 4300 Pa. However, Nickel Acetate and Cupper Acetate formed stable weak gels at low temperatures (50–70 °C) and a pH > 6 and gel decomposition was observed upon increasing the temperature. The developed formulations were compatible with low-salinity water (1000 ppm NaCl).
Scale deposition is a pertinent challenge in the oil and gas industry. Scales formed from iron sulfide are one of the troublous scales, particularly pyrite. Moreover, the use of biodegradable environmentally friendly chemicals reduces the cost compared to the conventional removal process. In this work, the chelating abilities of four novel chemicals, designed using the in silico technique of density functional theory (DFT), are studied as potential iron sulfide scale removers. Only one of the chemicals containing a hydroxamate functional group had a good chelating ability with Fe2+. The chelating strength and ecotoxicological properties of this chemical were compared to diethylenetriaminepentaacetic acid (DTPA), an already established iron sulfide scale remover. The new promising chemical surpassed DTPA in being a safer chemical and having a greater binding affinity to Fe2+ upon optimization, hence, a better choice. The presence of oxime (-NHOH) and carbonyl (C=O) moieties in the new chemical showed that the bidentate form of chelation is favored. Moreover, the presence of an intramolecular hydrogen bond enhanced its chelating ability.
Sulfate-reducing bacteria (SRB), such as Desulfobacter postgatei are found in oil wells. However, they lead to the release of hydrogen sulfide. This in turn leads to the iron sulfide scale formation (pyrite). ATP sulfurylase is an enzyme present in SRB, which catalyzes the formation of adenylyl sulfate (APS) and inorganic pyrophosphatase (PPi) from ATP and sulfate. This reaction is the first among many in hydrogen sulfide production by D. postgatei. Consensus scoring using molecular docking and machine learning was used to identify three potential inhibitors of ATP sulfurylase from a database of about 40 million compounds. These selected hits ((S,E)-1-(4-methoxyphenyl)-3-(9-((m-tolylimino)methyl)-9,10-dihydroanthracen-9-yl)pyrrolidine-2,5-dione; methyl 2-[[(1S)-5-cyano-2-imino-1-(4-phenylthiazol-2-yl)-3-azaspiro[5.5]undec-4-en-4-yl]sulfanyl]acetate; and (4S)-4-(3-chloro-4-hydroxy-phenyl)-1-(6-hydroxypyridazin-3-yl)-3-methyl-4,5-dihydropyrazolo[3,4-b]pyridin-6-ol), known as A, B, and C, respectively) all had good binding affinities with ATP sulfurylase and were further analyzed for their toxicological properties. Compound A had the highest docking score. However, based on the physicochemical and toxicological properties, only compound C was predicted to be both safe and effective as a potential inhibitor of ATP sulfurylase, hence the preferred choice. The molecular interactions of compound C revealed favorable interactions with the following residues: LEU213, ASP308, ARG307, TRP347, LEU224, GLN212, MET211, and HIS309.
Sulfate-reducing bacteria (SRB) such as Desulfobacter postgatei are often found in oil and gas wells. However, they lead to the release of hydrogen sulfide which in turn leads to the formation of iron sulfide scale such as pyrite. ATP sulfurylase is an enzyme present in SRB, which catalyzes the formation of adenylyl sulfate (APS) and inorganic pyrophosphatase (PPi) from ATP and sulfate which is one of the first steps in hydrogen sulfide production by D. postgatei . Virtual screening using molecular docking and machine learning tools was used to identify three potential inhibitors of ATP sulfurylase from a database of about 40 million compounds. These selected hits ((S,E)-1-(4-methoxyphenyl)-3-(9-((m-tolylimino)methyl)-9,10-dihydroanthracen-9-yl)pyrrolidine-2,5-dione;,methyl 2-[[(1S)-5-cyano-2-imino-1-(4-phenylthiazol-2-yl)-3-azaspiro[5.5]undec-4-en-4-yl]sulfanyl]acetate and (4S)-4-(3-chloro-4-hydroxy-phenyl)-1-(6-hydroxypyridazin-3-yl)-3-methyl-4,5-dihydropyrazolo[3,4-b]pyridin-6-ol), which are known as A, B and C respectively) all had good binding affinities with ATP sulfurylase and were further analyzed for their toxicological properties. The molecular docking results showed that all the compounds have negative binding energy with compound A having the highest docking score. However, based on the physicochemical and toxicological properties, compound C is the best choice as it does not violate any of the recommended properties that relate to absorption and distribution. Only compound C was predicted to be both safe and effective as a potential inhibitor of ATP sulfurylase. The binding mode of compound C revealed favorable interactions with the amino residues LEU 213, ASP 308, ARG 307, TRP 347, LEU 224, GLN 212, MET211 and HIS 309. Importance: Scale formation formed by hydrogen sulfide, which is produced by sulfate reducing bacteria such as Desulfobacter postgatei has been a persistent problem in the oil and gas industry leading to loss of money, time and even lives. The three selected hits from the virtual screenings of about 40 million compounds would possibly inhibit the enzyme, ATP sulfurylase, which is involved in the first reaction in hydrogen sulfide formation in Desulfobacter postgatei . The selected inhibitors are expected to significantly reduce the formation of hydrogen sulfide and consequently prevent the development of pyrite scale in oil and gas wells.