This article presents a high-performance radio frequency (RF) power amplifier (PA) module for which an optimum chip-level packaging structure is proposed to reduce the operating temperature of the RF PA monolithic microwave integrated circuit (MMIC). Because the output power ( P out ) and the efficiency of an RF PA module are strongly affected by the thermal characteristics of the PA MMIC, various types of heat spreader materials and thermal interface materials have been examined to implement the PA chip-level packaging structure, and the optimum combination is proposed for a performance enhancement of the PA module in this article. In addition, the optimum form-factor of the heat spreader was suggested based on a thermal simulation. To verify the proposed PA chip-level packaging structure, a 10 W 6–18 GHz RF PA MMIC using a commercial 0.25- μ m gallium nitride high electron mobility transistor process was designed and implemented for radar applications. The operating temperature of the PA MMIC on the proposed chip-level packaging structure shows a dramatic reduction of 24.8 °C, and accordingly, the average P out and average power-added efficiency are enhanced by up to 9.2% and 2.8%, respectively, when compared with a PA module using the conventional chip-level packaging structure.
Two-stage reactively matched gain cells are applied to design a high-gain multi-octave distributed power amplifier (DPA) in this paper. The proposed reactively matched distributed amplifier (RMDA) structure shows a high gain and high output power performance within a small die size. The DC bias network of each section is simplified to implement the proposed structure in an MMIC and the design guide for the bias network is provided. A 6-18 GHz GaN DPA fabricated with the commercial 0.25-μm GaN HEMT process shows output power reaching 40.3-43.9 dBm with 16-27% PAE. To the best of our knowledge, this is the first demonstration of a GaN DPA using reactively matched gain cells, and it exhibits excellent small-signal gain and RF power performance capabilities among other reported GaN PAs with a multi-octave bandwidth up to the Ku-band.
This paper presents a novel multi-channel type RF source module with solid-state power amplifiers for plasma generators. The proposed module is consisted of a DC control part, RF source generation part, and power amplification part. A 2-stage power amplifier (PA) is combined with a gallium arsenide hetero bipolar transistor (GaAs HBT) as a drive PA and a gallium nitride high electron mobility transistor (GaN HEMT) as a main PA, respectively. By employing 8 channels, the proposed module secures better area coverage on the wafer during semiconductor processes such as chemical vapor deposition (CVD), etching and so on. Additionally, each channel can be maintained at a constant output power because they have a gain factor tunable by a variable gain amplifier (VGA). For that reason, it is possible to have uniform plasma density on the wafer. The operating sequence is controllable by an external DC control port. Moreover, copper–tungsten (CuW) heat spreaders were applied to prevent RF performance degradation from heat generated by the high power amplifier (HPA), and a water jacket was implemented at the bottom of the power amplification part for liquid cooling. Drawing upon the measurement results, the output power at each channel was over 43 dBm (20 W) and the drain efficiency was more than 50% at 2.4 GHz.
This paper presents a 2.4 GHz 20 W 8-channel radio frequency (RF) source module with improved channel output balance. The proposed RF source module is composed of an RF source generation/DC control part, a power amplification part, and a power dividing part. A 2-stage power amplifier (PA) is combined with gallium nitride high-electron-mobility transistors, including a 25 W transistor and 2-way combined 120 W transistors as the drive and main PA, respectively. In addition, a structure was applied to improve the channel output balance compared to that of the previous module, and the differences of the phase and magnitude of the output power between channels are alleviated within 0.35° and 0.18 dB, respectively. A water jacket was implemented under the drive and main PAs for liquid cooling; however, unlike in the previous work, it was designed by optimizing the size of the water jacket and reducing unnecessary materials using a brazing process. The output power at each channel was 43 dBm, and the drain efficiency was more than 50% at 2.4 GHz. The total module size was 244 mm × 247.4 mm × 30 mm, and its volume was reduced by approximately 58.4% compared to that of the previous module.