Junghyun Kim

Junghyun Kim

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 January 2018 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
SKSungyoon Kang
Sungyoon Kang
MJMoon-Suk Jeon
Moon-Suk Jeon
JKJunghyun Kim
Junghyun Kim
A highly efficient fully integrated 5.15- to 5.85-GHz GaAs HBT differential power amplifier (PA) is implemented for long-term evolution (LTE) handset applications considering LTE licensed-assisted access. A simple and practical output network, based on an on-chip transformer, is proposed to achieve low loss. A neutralization technique to mitigate the parasitic base-collector capacitance is also adopted to improve PA performances. The implemented PA achieved a high gain of 26.6-28.1 dB and saturated power of 30.5-31.1 dBm with a high peak power-added efficiency of 40.4%-44.5% under a continuous-wave signal test across 5.15-5.85 GHz. When tested with 20- and 40-MHz bandwidth quadrature phase-shift keying LTE signals, the PA showed an adjacent channel leakage ratio of -33 dBc up to output powers of 24.1-24.4 and 22.2-22.8 dBm, respectively.

15 November 2018 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
KCKwangseok Choi
Kwangseok Choi
HPHongjong Park
Hongjong Park
MKMinchul Kim
Minchul Kim
JKJunghyun Kim
Junghyun Kim
YKYoungwoo Kwon
Youngwoo Kwon
In this paper, a switchless dual-band, dual-mode power amplifier (PA) has been developed for multioctave operation. For the switchless dual-band operation, we proposed a new coupled-line-based diplexer structure. The proposed diplexer operates as a balun at high-band frequencies and the coupled line at low-band frequencies. To better understand the proposed diplexer structure, a detailed analysis is performed based on a coupled-line theory. The interstage and output-stage matching networks of the PA are designed by using the proposed diplexer. To maximize the power-added efficiency (PAE) of the designed PA, turn off the unused band PAs and decide the optimum off-state bias condition of transistors. The designed dual-band, dual-mode PA is fabricated with commercial 0.25-μm GaN HEMT process. The fabricated PA shows over 15-dB small-signal gain at 5-11 GHz in the low-band mode and 9-18 GHz in the high-band mode. The measured average output power and PAE are 35 dBm, 23% in the low-band mode and 37 dBm, 26% in the high-band mode.

17 October 2023 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
SHSungwoon Hwang
Sungwoon Hwang
JJJooyoung Jeon
Jooyoung Jeon
BSBae sooji
Bae sooji
BYByeongcheol Yoon
Byeongcheol Yoon
SKSungyoon Kang
Sungyoon Kang
JKJunghyun Kim
Junghyun Kim
This article presents a 5.15–7.125-GHz differential power amplifier (PA) with enhanced linear output power by dynamic cross-coupled capacitors ( $C_{\text{cc}}$ ) for both fifth-generation new radio-unlicensed (5G NR-U) and 802.11ax wireless local area network (WLAN) applications. The proposed dynamic $C_{\text{cc}}$ compensates for nonlinear parameters of transistors and leads to improved linearity in the average output power region. The multicoupled four-way transformer (TF) is also proposed for a high symmetry combining structure to reduce the imbalance of differential PA and for a 30% fractional bandwidth of optimal output matching with a low turn ratio and low insertion losses to implement on a nine-layer printed circuit board applications. The proposed differential PA is implemented in a 2- $\mu\text{m}$ InGaP/GaAs heterojunction bipolar transistor (HBT) process. The PA achieves a gain of 24 dB, a saturated output power of 33.1 dBm, and a power added efficiency (PAE) of 40.4% with a collector voltage of 5.5 V over 5.15–7.125 GHz under a continuous wave (CW) signal. The linearity of the proposed PA is further evaluated with various modulation signal schemes to validate its suitability for NR-U and WLAN applications. The PA with NR 100-MHz cyclic prefix (CP) and discrete Fourier transform (DFT) signal having a peak-to-average power ratio (PAPR) of 11.4 and 8 dB achieves linear output power meeting $-$ 33 dBc of 24.6 and 27 dBm and PAE of 10% and 16.3% in NR evolved universal terrestrial radio access (E-UTRA) adjacent channel leakage ratio (ACLR) condition. The PA also achieves the output power of 19.8 dBm with a PAE of 4.3% (error vector magnitude (EVM) $=$ $-$ 40 dB) under 802.11ax MCS11 80 MHz having a PAPR of 10.7 dB.

16 June 2021 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
HNHyosung Nam
Hyosung Nam
JKJihoon Kim
Jihoon Kim
JJJooyoung Jeon
Jooyoung Jeon
HJHeesauk Jhon
Heesauk Jhon
JKJunghyun Kim
Junghyun Kim
This article presents a high-performance radio frequency (RF) power amplifier (PA) module for which an optimum chip-level packaging structure is proposed to reduce the operating temperature of the RF PA monolithic microwave integrated circuit (MMIC). Because the output power ( P out ) and the efficiency of an RF PA module are strongly affected by the thermal characteristics of the PA MMIC, various types of heat spreader materials and thermal interface materials have been examined to implement the PA chip-level packaging structure, and the optimum combination is proposed for a performance enhancement of the PA module in this article. In addition, the optimum form-factor of the heat spreader was suggested based on a thermal simulation. To verify the proposed PA chip-level packaging structure, a 10 W 6–18 GHz RF PA MMIC using a commercial 0.25- μ m gallium nitride high electron mobility transistor process was designed and implemented for radar applications. The operating temperature of the PA MMIC on the proposed chip-level packaging structure shows a dramatic reduction of 24.8 °C, and accordingly, the average P out and average power-added efficiency are enhanced by up to 9.2% and 2.8%, respectively, when compared with a PA module using the conventional chip-level packaging structure.

18 January 2023 in IEEE Access
Verified
Journal Article
Open access
WSWonwoo Seo
Wonwoo Seo
SKSunghyuk Kim
Sunghyuk Kim
BKByunghun Ko
Byunghun Ko
HJHeesauk Jhon
Heesauk Jhon
JKJunghyun Kim
Junghyun Kim
This paper presents a fast switching and high-powered single-pole double-throw (SPDT) switch for RF switch circuits, such as TRx antenna switches and frequency band (or operation mode) selection switches in mobile handset applications. For fast switching time and performances of the RF switch, we proposed a novel method that can “selectively” control the impedance of a gate biasing circuit (“high” or “low” impedance). The proposed SPDT switch use the low impedance of the gate biasing circuit for fast switching time and use the high impedance of the gate biasing circuit to avoid the degradation of insertion loss and harmonics. The proposed SPDT switch has no additional bias and no large payment for size consumption. According to measurement results, the turn-on switching time of the proposed SPDT switch was 0.35 μs (at 2 GHz). The insertion loss, isolation, and return loss at 2 GHz were 0.16 dB, 47.1 dB, and 24 dB respectively. 2nd and 3rd harmonic levels at 25 dBm input power at 2 GHz were –88.7 dBm and –78.9 dBm, respectively. Power handling capability was 39.5 dBm of input power at 2 GHz. The designed SPDT switch was implemented in a 0.13-μm partially depleted silicon-on-insulator (PD-SOI) process.

13 June 2023 in IEEE Access
Verified
Journal Article
Open access
TJTae Hwan Jang
Tae Hwan Jang
ALAhnwoo Lee
Ahnwoo Lee
SKSunghyuk Kim
Sunghyuk Kim
HLHee Sung Lee
Hee Sung Lee
JLJaesuk Lee
Jaesuk Lee
JKJunghyun Kim
Junghyun Kim
In this work, a millimeter-wave wideband wide beamwidth modified angled dipole antenna is proposed for 5G millimeter-wave(mmW) IoT applications. The modified angled dipole antenna which has a dipole arm that is bent once more perpendicular to the ground plane compared to the existing angled dipole is proposed to improve not only the beamwidth but also the S11 bandwidth. The image current is formed in the direction perpendicular to the ground by the dipole arm bent to be orthogonal to the ground. Because only the E-field in the direction perpendicular to the ground can be formed by the boundary condition, the E-field radiated from the proposed antenna can be radiated along the ground plane, and thus the E-plane beamwidth is widened, and the H–plane beamwidth can be widened. The measured -10dB S 11 bandwidth is 5GHz(=17.8%) ranging from 25.7GHz to 30.7 GHz, and the measured HPBW is 160° ±5 ° and 310°±10° for the E-plane and H-plane, respectively. To verify whether the proposed antenna is practically applied to 5G IoT applications, the beamforming IC was connected to the proposed antenna array, and the E-plane beam-forming radiation pattern was measured. Although it was applied only to the -90 ° ≤ β ≤ 90 ° range, the -3dB E-plane beamwidth was 130°, ensuring wide coverage.