Taejoo Sim

Mr. Taejoo Sim

Hanyang University

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 June 2023 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
BKByunghun Ko
Byunghun Ko
SLSunwoo Lee
Sunwoo Lee
WSWonwoo Seo
Wonwoo Seo
TSTaejoo Sim
Taejoo Sim
SKSunghyuk Kim
Sunghyuk Kim
JKJunghyun Kim
Junghyun Kim
This paper presents a switchless dual-band low-noise amplifier (LNA) that can be reconfigured to include n260 (37.40 GHz) and n262 (47.2.48.2 GHz) millimeter-wave (mm-Wave) dual bands. The proposed reconfigurable LNA is designed to separate and isolate two bands, using a common gate and coupled-line-based diplexer for the inter-stage of cascade amplifiers. A common gate amplifier has the advantage of simultaneously selecting the signal path and amplifying the signal power according to a band, using an impedance variation between the gon/offh conditions of gate bias. In addition, the coupled-line-based diplexer can be optimized to exhibit high isolation characteristics between frequencies using high and low-pass characteristics. The designed reconfigurable LNA is fabricated with the 0.15–μm GaAs pHEMT process. With the high frequency (HF) mode, the reconfigurable LNA achieves a measured gain of 19.2 dB at the center frequency, noise figure, and OP1dB of 48 GHz, 4.8 dB, and 6.88 dBm, respectively. In the low frequency (LF) mode, the reconfigurable LNA exhibits a measured gain of 24.8 dB at the center frequency, noise figure, and OP1dB of 39 GHz, 3.9 dB, and 6.80 dBm, respectively. The chip occupies a core area of 3.04 mm2, which consumes 61.4 mW and 64.7 mW in the HF and LF modes, respectively.

26 August 2020 in Electronics
Verified
Journal Article
Open access
PDF file
HNHyosung Nam
Hyosung Nam
TSTaejoo Sim
Taejoo Sim
JKJunghyun Kim
Junghyun Kim
This paper presents a novel multi-channel type RF source module with solid-state power amplifiers for plasma generators. The proposed module is consisted of a DC control part, RF source generation part, and power amplification part. A 2-stage power amplifier (PA) is combined with a gallium arsenide hetero bipolar transistor (GaAs HBT) as a drive PA and a gallium nitride high electron mobility transistor (GaN HEMT) as a main PA, respectively. By employing 8 channels, the proposed module secures better area coverage on the wafer during semiconductor processes such as chemical vapor deposition (CVD), etching and so on. Additionally, each channel can be maintained at a constant output power because they have a gain factor tunable by a variable gain amplifier (VGA). For that reason, it is possible to have uniform plasma density on the wafer. The operating sequence is controllable by an external DC control port. Moreover, copper–tungsten (CuW) heat spreaders were applied to prevent RF performance degradation from heat generated by the high power amplifier (HPA), and a water jacket was implemented at the bottom of the power amplification part for liquid cooling. Drawing upon the measurement results, the output power at each channel was over 43 dBm (20 W) and the drain efficiency was more than 50% at 2.4 GHz.

15 August 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HNHyosung Nam
Hyosung Nam
TKTaewan Kim
Taewan Kim
TSTaejoo Sim
Taejoo Sim
BSBae sooji
Bae sooji
JKJunghyun Kim
Junghyun Kim
This paper presents a 2.4 GHz 20 W 8-channel radio frequency (RF) source module with improved channel output balance. The proposed RF source module is composed of an RF source generation/DC control part, a power amplification part, and a power dividing part. A 2-stage power amplifier (PA) is combined with gallium nitride high-electron-mobility transistors, including a 25 W transistor and 2-way combined 120 W transistors as the drive and main PA, respectively. In addition, a structure was applied to improve the channel output balance compared to that of the previous module, and the differences of the phase and magnitude of the output power between channels are alleviated within 0.35° and 0.18 dB, respectively. A water jacket was implemented under the drive and main PAs for liquid cooling; however, unlike in the previous work, it was designed by optimizing the size of the water jacket and reducing unnecessary materials using a brazing process. The output power at each channel was 43 dBm, and the drain efficiency was more than 50% at 2.4 GHz. The total module size was 244 mm × 247.4 mm × 30 mm, and its volume was reduced by approximately 58.4% compared to that of the previous module.

30 November 2023 in Journal of Electromagnetic Engineering and Science
Verified
Journal Article
Open access
PDF file
TSTaejoo Sim
Taejoo Sim
DLDong-Min Lee
Dong-Min Lee
WKWansik Kim
Wansik Kim
KKKichul Kim
Kichul Kim
JCJeung Won Choi
Jeung Won Choi
JKJunghyun Kim
Junghyun Kim
In this study, a dual-band low-noise amplifier (LNA) was implemented by applying a transformer-based neutralization technology to the W-band. Incorporating the neutralization technique was difficult owing to performance degradation in the W-band. However, circuit performance was enhanced thanks to the layout optimization of transformer-based neutralization networks, and the improved operation was confirmed in the W-band. The neutralization technique was implemented in four stages with a 0.1-μm gallium arsenide (GaAs) pseudomorphic high-electron-mobility-transistor monolithic microwave integrated circuit LNA. The LNA showed small signal gains of 20.3 dB and 21.7 dB and noise figures of 5.0 dB and 6.4 dB (at 84 GHz and 96 GHz, respectively) while consuming 46 mW from a 1-V supply.

1 January 2026 in IEEE Access
Verified
Journal Article
Open access
TSTaejoo Sim
Taejoo Sim
IPInsu Park
Insu Park
NCNamcheol Chang
Namcheol Chang
DLDongmin Lee
Dongmin Lee
WCWonseok Choe
Wonseok Choe
JKJunghyun Kim
Junghyun Kim