Five kinds of multi-component entropy-stabilized oxide ceramics were prepared by a solid-state reaction method for thermal barrier coatings, namely La0.125Y0.125Yb0.125Gd0.125Zr0.5O1.75 (LaYYbGdZr), Y0.125Yb0.125Gd0.125Ta0.125Zr0.5O1.875 (YYbGdTaZr), La0.1Y0.1Yb0.1Gd0.1Ta0.1Zr0.5O1.85 (LaYYbGdTaZr), Y0.125Yb0.125Gd0.125Ta0.125Hf0.25Zr0.25O1.875 (YYbGdTaHfZr), and La0.1Y0.1Yb0.1Gd0.1Ta0.1Hf0.25Zr0.25O1.85 (LaYYbGdTaHfZr). Many properties of the materials were studied, such as their microscopic morphology, crystal structure, thermophysical properties, and ablation resistance. The results show that the oxide ceramics synthesized in this paper have a uniform single-phase defect fluorite structure, and can still maintain this structure after high-temperature treatment at 1500 °C. The YYbGdTaHfZr coatings had the lowest thermal conductivity (0.61~0.89 W·m–1·K–1), which was much lower than that of YSZ. The ceramic blocks also exhibited excellent thermal expansion properties. The thermal expansion coefficient of LaYYbGdTaZr could reach 11.09 × 10−6 K−1 (1400 °C), which was slightly higher than that of 8YSZ (11.0 × 10−6 K−1). The antioxidant ablation results proved that the YYbGdTaHfZr coating showed the best heat-insulating property. All the results showed that the YYbGdTaHfZr coating is a promising thermal barrier coating.
Gel polymer electrolytes have the advantages of both a solid electrolyte and a liquid electrolyte. As a transitional product before which a solid electrolyte can be comprehensively used, gel polymer electrolytes are of great research value. They can reduce the risk of spontaneous combustion and explosion caused by leakage during the use of conventional liquid electrolytes. Poly(vinylidene-fluoride-co-hexafluoropropylene) (PVDF–HFP), a material with excellent performance, has been widely utilized in the preparation of gel polymer electrolytes. Here, PVDF–HFP-based gel polymer membranes with polyvinyl pyrrolidone (PVP) pores were prepared using a phase inversion method, and Octavinyl-polyhedral oligomeric silsesquioxane (OVAPOSS) was doped to improve its temperature resistance as well as its ionic conductivity, to enhance its safety and electrochemical performance. The final prepared polymer membrane had a porosity of 85.06% and still had a certain mechanical strength at 160 °C without any shrinkage. The gel polymer electrolyte prepared with this polymer membrane had an ionic conductivity of 1.62 × 10−3 S·cm−1 at 30 °C, as well as an electrochemical window of about 5.5 V. The LiCoO2-Li button half-cell prepared therefrom had a specific capacity of 141 mAh·g−1 at a rate of 1C. The coulombic efficiency remained above 99% within 100 cycles and the capacity retention rate reached 99.5%, which reveals an excellent cycling stability.
As a cathode material for thermal batteries, WS 2 has high thermal decomposition temperature and large specific capacity, but it is an intermittent semiconductor, with relatively low conductivity. This low conductivity can prolong the activation time and reduce the discharge specific capacity of thermal batteries. Here, we prepared WS 2 with sulfur vacancies through a simple high-temperature annealing method and used electron paramagnetic resonance spectroscopy and X-ray photoelectron spectroscopy to detect the presence of sulfur vacancies. The result shows that sulfur vacancies were successfully introduced in WS 2 , and the existence of sulfur vacancies can effectively improve the discharge performance of thermal batteries. While maintaining the nanostructure, the thermal decomposition temperature still exceeds 1000 °C, which is far beyond the traditional FeS 2 (550 °C) and CoS 2 (650 °C) cathodes. The Li-B/LiF-LiBr-LiCl/WS 2 with sulfur vacancies (treated at 500 °C) couple has higher discharge specific capacity (when the cut-off voltage is 0.5 V, it is 380.58 mAh g −1 , which is 14.85% higher than the original WS 2 ) and lower total polarization (about 21% lower than original WS 2 ). This work provides a beginning for further study of sulfur vacancies defect materials as the cathode of thermal batteries.