Five kinds of multi-component entropy-stabilized oxide ceramics were prepared by a solid-state reaction method for thermal barrier coatings, namely La0.125Y0.125Yb0.125Gd0.125Zr0.5O1.75 (LaYYbGdZr), Y0.125Yb0.125Gd0.125Ta0.125Zr0.5O1.875 (YYbGdTaZr), La0.1Y0.1Yb0.1Gd0.1Ta0.1Zr0.5O1.85 (LaYYbGdTaZr), Y0.125Yb0.125Gd0.125Ta0.125Hf0.25Zr0.25O1.875 (YYbGdTaHfZr), and La0.1Y0.1Yb0.1Gd0.1Ta0.1Hf0.25Zr0.25O1.85 (LaYYbGdTaHfZr). Many properties of the materials were studied, such as their microscopic morphology, crystal structure, thermophysical properties, and ablation resistance. The results show that the oxide ceramics synthesized in this paper have a uniform single-phase defect fluorite structure, and can still maintain this structure after high-temperature treatment at 1500 °C. The YYbGdTaHfZr coatings had the lowest thermal conductivity (0.61~0.89 W·m–1·K–1), which was much lower than that of YSZ. The ceramic blocks also exhibited excellent thermal expansion properties. The thermal expansion coefficient of LaYYbGdTaZr could reach 11.09 × 10−6 K−1 (1400 °C), which was slightly higher than that of 8YSZ (11.0 × 10−6 K−1). The antioxidant ablation results proved that the YYbGdTaHfZr coating showed the best heat-insulating property. All the results showed that the YYbGdTaHfZr coating is a promising thermal barrier coating.
Gel polymer electrolytes have the advantages of both a solid electrolyte and a liquid electrolyte. As a transitional product before which a solid electrolyte can be comprehensively used, gel polymer electrolytes are of great research value. They can reduce the risk of spontaneous combustion and explosion caused by leakage during the use of conventional liquid electrolytes. Poly(vinylidene-fluoride-co-hexafluoropropylene) (PVDF–HFP), a material with excellent performance, has been widely utilized in the preparation of gel polymer electrolytes. Here, PVDF–HFP-based gel polymer membranes with polyvinyl pyrrolidone (PVP) pores were prepared using a phase inversion method, and Octavinyl-polyhedral oligomeric silsesquioxane (OVAPOSS) was doped to improve its temperature resistance as well as its ionic conductivity, to enhance its safety and electrochemical performance. The final prepared polymer membrane had a porosity of 85.06% and still had a certain mechanical strength at 160 °C without any shrinkage. The gel polymer electrolyte prepared with this polymer membrane had an ionic conductivity of 1.62 × 10−3 S·cm−1 at 30 °C, as well as an electrochemical window of about 5.5 V. The LiCoO2-Li button half-cell prepared therefrom had a specific capacity of 141 mAh·g−1 at a rate of 1C. The coulombic efficiency remained above 99% within 100 cycles and the capacity retention rate reached 99.5%, which reveals an excellent cycling stability.
The pervasive dissolution of transition metal fluoride (TMF) cathodes presents a fundamental barrier to their application in high‐voltage thermal batteries and other Li + ‐conducting systems. Herein, we report a novel selective confinement strategy inspired by ion sieving to overcome this challenge by constructing a sub‐nanoporous carbon interface in situ on CoF 2 particles. Derived from a covalent organic framework (COF), this interface features precisely defined 0.54 nm pores that exploit the size difference between Li + ions (∼0.15 nm) and dissolved transition metal fluoride derived complex ions (∼0.8 nm), effectively confining the active material while enabling unimpeded ionic conduction. This tailored design successfully suppresses cathode shuttling effect, enabling a thermal battery that delivers an exceptional discharge plateau >2.5 V, a high specific capacity of 365 mAh g −1 , and a remarkable specific energy of 882 Wh kg −1 at 100 mA cm −2 . Mechanism studies confirm the dissolved transition metal fluoride derived complex ions as CoCl 42− and efficient confinement of it. This work provides a general and effective interface engineering strategy for unlocking the full potential of metal fluoride cathodes in advanced energy storage.