Iron trifluoride (FeF3) might be a suitable high-voltage cathode material for high-power thermal batteries due to its high voltage plateau, low cost and low toxicity. In this study, anhydrous FeF3 was synthesized and its applicability as a cathode material for thermal batteries was investigated. Its structure, thermal stability and electrochemical properties were also studied. The synthesized anhydrous FeF3 had a hierarchical structure and a decomposition threshold temperature of 800°C. At a current density of 100 mA cm−2, the Li-B/FeF3 single cell exhibited an initial discharge voltage of 3.20 V and a specific capacity of 81.9 mA h g−1 with a cutoff voltage of 2.0 V. Moreover, multi-walled carbon nanotubes (MWCNTs) were used as the conductive agents, leading to an decreasing of the total polarization from 45 mΩ to 10 mΩ. In specific, the Li-B/ FeF3-MWCNTs single cell exhibited an initial discharge voltage of 3.27 V and a specific capacity of 160.7 mAh·g−1. This work provides a beginning for further applying FeF3 as a high-voltage cathode material for high-power thermal batteries.
Five kinds of multi-component entropy-stabilized oxide ceramics were prepared by a solid-state reaction method for thermal barrier coatings, namely La0.125Y0.125Yb0.125Gd0.125Zr0.5O1.75 (LaYYbGdZr), Y0.125Yb0.125Gd0.125Ta0.125Zr0.5O1.875 (YYbGdTaZr), La0.1Y0.1Yb0.1Gd0.1Ta0.1Zr0.5O1.85 (LaYYbGdTaZr), Y0.125Yb0.125Gd0.125Ta0.125Hf0.25Zr0.25O1.875 (YYbGdTaHfZr), and La0.1Y0.1Yb0.1Gd0.1Ta0.1Hf0.25Zr0.25O1.85 (LaYYbGdTaHfZr). Many properties of the materials were studied, such as their microscopic morphology, crystal structure, thermophysical properties, and ablation resistance. The results show that the oxide ceramics synthesized in this paper have a uniform single-phase defect fluorite structure, and can still maintain this structure after high-temperature treatment at 1500 °C. The YYbGdTaHfZr coatings had the lowest thermal conductivity (0.61~0.89 W·m–1·K–1), which was much lower than that of YSZ. The ceramic blocks also exhibited excellent thermal expansion properties. The thermal expansion coefficient of LaYYbGdTaZr could reach 11.09 × 10−6 K−1 (1400 °C), which was slightly higher than that of 8YSZ (11.0 × 10−6 K−1). The antioxidant ablation results proved that the YYbGdTaHfZr coating showed the best heat-insulating property. All the results showed that the YYbGdTaHfZr coating is a promising thermal barrier coating.
Gel polymer electrolytes have the advantages of both a solid electrolyte and a liquid electrolyte. As a transitional product before which a solid electrolyte can be comprehensively used, gel polymer electrolytes are of great research value. They can reduce the risk of spontaneous combustion and explosion caused by leakage during the use of conventional liquid electrolytes. Poly(vinylidene-fluoride-co-hexafluoropropylene) (PVDF–HFP), a material with excellent performance, has been widely utilized in the preparation of gel polymer electrolytes. Here, PVDF–HFP-based gel polymer membranes with polyvinyl pyrrolidone (PVP) pores were prepared using a phase inversion method, and Octavinyl-polyhedral oligomeric silsesquioxane (OVAPOSS) was doped to improve its temperature resistance as well as its ionic conductivity, to enhance its safety and electrochemical performance. The final prepared polymer membrane had a porosity of 85.06% and still had a certain mechanical strength at 160 °C without any shrinkage. The gel polymer electrolyte prepared with this polymer membrane had an ionic conductivity of 1.62 × 10−3 S·cm−1 at 30 °C, as well as an electrochemical window of about 5.5 V. The LiCoO2-Li button half-cell prepared therefrom had a specific capacity of 141 mAh·g−1 at a rate of 1C. The coulombic efficiency remained above 99% within 100 cycles and the capacity retention rate reached 99.5%, which reveals an excellent cycling stability.
Thermal barrier coatings have been used to protect superalloys under extremely harsh conditions. The durability of TBCs with a NiCoCrAlY bond layer prepared via the air plasma spray process and an ultrathin dense layer prepared via magnetron sputtering was investigated under different corrosion conditions. This paper discusses the corrosion resistance improvement mechanism of TBCs with a dense layer produced by magnetron sputtering under corrosion conditions with environmental contaminants such as calcium–magnesium–aluminum–silicon oxide systems (CMAS) at 1300 °C and NaCl-Na2SO4-V2O5 (NV) at 900 °C. The corrosion results show that CMAS will react with the stabilizers of zirconium oxide, which will change the rate of the phase transition, as determined via X-ray diffraction tests. A thermal ablation test verified that TBCs with a dense layer have a better corrosion resistance and better thermal insulation properties. All results show that preparing TBCs with a dense layer via the magnetron sputtering method will be an efficient method to improve TBCs’ properties at high temperatures in the future.