By means of X-ray computed microtomography (XCMT), the existence of a developed porous structure with an average pore diameter of ~3.5 μm and pore content of ~1.1 vol.% has been revealed in unirradiated polytetrafluoroethylene (PTFE). It has been found that the combined action of gamma radiation (absorbed dose per PTFE of ~170 kGy) and high temperatures (327–350 °C) leads to the disappearance of the porous structure and the formation of several large pores with sizes from 30 to 50 μm in the bulk of thermal-radiation modified PTFE (TRM-PTFE). It has been established by X-ray diffraction (XRD) analysis that the thermal-radiation modification of PTFE leads to an increase in the interplanar spacings, the degree of crystallinity and the volume of the unit cell, as well as to a decrease in the size of crystals and the X-ray density of the crystalline phase in comparison with the initial polymer. It is assumed that the previously-established effect of improving the deformation-strength and tribological properties of the TRM-PTFE can be due not only to the radiation cross-linking of polymer chains but also to the disappearance of the pore system and to the ordering of the crystalline phase of PTFE.
1 June 2023 in Russian Journal of Physical Chemistry B
Studies on modeling the charge distribution in semiconductor nanoparticles are analyzed. The charge distribution largely depends on the type of nanoparticles and the concentration of conduction electrons. In the case of nanoparticles with a high content of electrons in the conduction band, the negatively charged layer plays an important role. The conductivity and sensor effect depend on this layer. It is shown that both the distribution of electrons and the sensor effect differ significantly in one- and two-component systems. The reasons for this difference are discussed.
The paper considers the relationship between the structure and properties of nanostructured conductometric sensors based on binary mixtures of semiconductor oxides designed to detect reducing gases in the environment. The sensor effect in such systems is determined by the chemisorption of molecules on the surface of catalytically active particles and the transfer of chemisorbed products to electron-rich nanoparticles, where these products react with the analyzed gas. In this regard, the role is evaluated of the method of synthesizing the composites, the catalytic activity of metal oxides (CeO2, SnO2, ZnO), and the type of conductivity of metal oxides (Co3O4, ZrO2) in the sensor process. The effect of oxygen vacancies present in the composites on the performance characteristics is also considered. Particular attention is paid to the influence of the synthesis procedure for preparing sensitive layers based on CeO2–In2O3 on the structure of the resulting composites, as well as their conductive and sensor properties.
The influence of the method used for synthesizing ZnO-In2O3 composites (nanopowder mixing, impregnation, and hydrothermal method) on the structure, conductivity, and sensor properties is investigated. With the nanopowder mixing, the size of the parent nanoparticles in the composite remains practically unchanged in the range of 50–100 nm. The impregnation composites consist of 70 nm In2O3 nanoparticles with ZnO nanoclusters < 30 nm in size located on its surface. The nanoparticles in the hydrothermal composites have a narrow size distribution in the range of 10–20 nm. The specific surface of hydrothermal samples is five times higher than that of impregnated samples. The sensor response of the impregnated composite to 1100 ppm H2 is 1.3–1.5 times higher than the response of the mixed composite. Additives of 15–20 and 85 wt.% ZnO to mixed and impregnated composites lead to an increase in the response compared with pure In2O3. In the case of hydrothermal composite, up to 20 wt.% ZnO addition leads to a decrease in response, but 65 wt.% ZnO addition increases response by almost two times compared with pure In2O3. The sensor activity of a hydrothermal composite depends on the phase composition of In2O3. The maximum efficiency is reached for the composite containing cubic In2O3 and the minimum for rhombohedral In2O3. An explanation is provided for the observed effects.
Cu-doped In2O3 nanocomposites with copper compositions of 1–3 wt.% are synthesized by a hydrothermal method using water or alcohol as a solvent. Cubic In2O3 is formed when water is used for synthesis, while composites synthesized in alcohol contain rhombohedral In2O3. This trend is independent of the amount of copper introduced. The Cu ions are shown to be uniformly distributed in the In2O3 nanoparticles without significant destruction of the indium oxide structure. All the composites exhibit a porous structure that depends on the solvent used for the synthesis. The addition of copper to both crystalline forms of indium oxide increases the resistance of the films and reduces the operating temperature. The phase state of indium oxide also affects the conductivity of the composites. There is an increase in sensory response to H2 and CO with the introduction of Cu into samples with cubic structure, but a reduction in response in samples with the rhombohedral phase of indium oxide.