Deformation measurements have a repeatable nature. This means that deformation measurements are performed often with the same equipment, methods, geometric conditions and in a similar environment in epochs 1 and 2 (e.g., a fully automated, continuous control measurements). It is, therefore, reasonable to assume that the results of deformation measurements can be distorted by both random errors and by some non-random errors, which are constant in both epochs. In other words, there is a high probability that the difference in the accuracy and precision of measurement of the same geometric element of the network in both epochs has a constant value and sign. The constant errors are understood, but the manifestation of these errors is difficult to determine in practice. For free control networks (the group of potential reference points in absolute control networks or the group of potential stable points in relative networks), the results of deformation measurements are most often processed using robust methods. Classical robust methods do not completely eliminate the effect of constant errors. This paper proposes a new robust alternative method called REDOD. The performed tests showed that if the results of deformation measurements were additionally distorted by constant errors, the REDOD method completely eliminated their effect from deformation analysis results. If the results of deformation measurements are only distorted by random errors, the REDOD method yields very similar deformation analysis results as the classical IWST method. The numerical tests were preceded by a theoretical part. The theoretical part describes the algorithm of classical robust methods. Particular attention was paid to the IWST method. In relation to classical robust methods, the optimization problem of the new REDOD method was formulated and the algorithm for its solution was derived.
24 April 2015 in International Journal of Remote Sensing
ALS point cloud filtering involves the separation of observations representing the physical terrain surface from those representing terrain details. A digital terrain model (DTM) is created from a subset of points representing the ground surface. The accuracy of the generated DTM is influenced by several factors, including the survey method used, the accuracy of the source data, the applied DTM generation algorithm, and the survey conditions. This article proposes the use of a new estimation method in the filtering of point clouds obtained from airborne laser scanning (ALS), provisionally called Msplit-estimation. The application of Msplit-estimation in ALS data filtering requires the determination of the appropriate functional model for the surface, which will be used in the filtering of the set of points. A polynomial terrain surface model was selected for this purpose. Two methods of filtering using the Msplit method are presented. The first is based on the estimated parameters of the polynomial describing the surface (called the ‘quality’ approach in the article). The second method (provisionally called the ‘quantity’ method) is carried out in two stages. The first stage is point cloud filtering, which results in two subsets being created. One of these is the subset of points intended for DTM creation, while the other contains the remaining points. The second stage of the approach is the creation of a DTM from the first subset. Since the Msplit method has an analytical character, the ATIN method was selected to verify the correct operation of the method. The ATIN method is based on computational geometry and uses repeated Delaunay triangulation and statistical evaluation of the geometric parameters. Comparison of Msplit with a method based on different principles mitigates errors arising from similarly functioning methods belonging to the same group of filters. The choice of the ATIN method was also dictated by its established position among filtering algorithms. The method is well-known, documented, and verified and this ensures that filtering by this method provides a reliable result that can serve as a reference for comparison with the proposed new filtering method. The theoretical discussion presented in this article was verified with two practical examples. The results obtained from computation by the Msplit method with appropriate terrain models encourage more detailed theoretical and empirical tests of this method for the filtering and segmentation of ALS data-sets.
1 December 2011 in Canadian Journal of Remote Sensing
Airborne laser scanning (ALS) provides survey results in the form of a point cloud. The ALS point cloud is a source of data used primarily for constructing a digital terrain model (DTM). To generate a DTM, the set of ALS observations must be first subjected to the point cloud processing methodology. A standard methodology is composed of the following stages: acquisition of the ALS data, initial processing (including filtration), and the main processing (including DTM generation). Problems primarily concerning the time span necessary for processing a very high number of observations occur at each of the stages mentioned above. In previous studies the authors proposed modification of the ALS point cloud methodology. The modification introduced an optimization algorithm to reduce the size of the survey dataset at the stage of initial processing. Those studies analyzed the “optimization–filtration” and “filtration–optimization” variants, applying methods based on the multi (M) estimation principle at the filt... Le scanneur laser aviaire (ALS) fournit des résultats de mesures sous forme de nuage de points. Le nuage de points ALS est une source de données surtout pour les besoins de la construction d’ un modèle numérique du terrain (DTM). Pour que l'ensemble des observations ALS puisse servir à générer un DTM, il doit d'abord être soumis à la méthodologie de l’élaboration d'un nuage de points. La méthodologie standard est composée des étapes suivantes: la collecte des données ALS, le traitement initial, dont la filtration et le traitement principal (dont la génération DTM). A chaque étape des problèmes apparaissent, concernant surtout le temps nécessaire au traitement d'un grand nombre d'observations. Dans leurs travaux les auteurs ont proposé une modification de la méthodologie d’élaboration de nuage de points ALS. Cette modification consistait en introduction à l’étape du traitement initial d'un algorithme d'optimisation diminuant le nombre de mesures. Dans les travaux ci-dessus on a analysé les variantes «optim...
25 June 2011 in Journal of the Indian Society of Remote Sensing
This paper proposes a method for determining the vertical deformations treated as random fields. It is assumed that the monitored surfaces are subject not only to deterministic deformations, but also to random fluctuations. Furthermore, the existence of random noise coming from surface’s vibrations is also assumed. Such noise disturbs the deformation’s functional models. Surface monitoring with the use of the geodetic levelling network of a free control network class is carried out. Assuming that, in some cases, the control networks are insufficient in surface’s deformation analysis, additional and non–measurable reference points have been provided. The prediction of these points’ displacements and estimation of the free control network points’ displacement are carried out using the collocation method applying the total least squares adjustment. The proposed theoretical solutions were verified by the simulation methods and on the example of a real control network.
Nowadays, hydrostatic levelling is a widely used method for the vertical displacements’ determinations of objects such as bridges, viaducts, wharfs, tunnels, high buildings, historical buildings, special engineering objects (e.g., synchrotron), sports and entertainment halls. The measurements’ sensors implemented in the hydrostatic levelling systems (HLSs) consist of the reference sensor (RS) and sensors located on the controlled points (CPs). The reference sensor is the one that is placed at the point that (in theoretical assumptions) is not a subject to vertical displacements and the displacements of controlled points are determined according to its height. The hydrostatic levelling rule comes from the Bernoulli’s law. While using the Bernoulli’s principle in hydrostatic levelling, the following components have to be taken into account: atmospheric pressure, force of gravity, density of liquid used in sensors places at CPs. The parameters mentioned above are determined with some mean errors that influence on the accuracy assessment of vertical displacements. In the subject’s literature, there are some works describing the individual accuracy analyses of the components mentioned above. In this paper, the author proposes the concept of comprehensive determination of mean error of vertical displacement (of each CPs), calculated from the mean errors’ values of components dedicated for specific HLS. The formulas of covariances’ matrix were derived and they enable to make the accuracy assessment of the calculations’ results. The author also presented the subject of modelling of vertical displacements’ gained values. The dependences, enabling to conduct the statistic tests of received model’s parameters, were implemented. The conducted tests make it possible to verify the correctness of used theoretical models of the examined object treated as the rigid body. The practical analyses were conducted for two simulated variants of sensors’ connections in HLS. Variant no. I is the sensors’ serial connection. Variant no. II relies on the connection of each CPs with the reference sensor. The calculations’ results show that more detailed value estimations of the vertical displacements can be obtained using variant no. II.