Burnishing is a plastic deformation process that reduces roughness while increasing hardness by introducing compressive residual stresses near the surface zone. These improvements will depend mainly on two fundamental variables: the applied load and the friction derived from the tool–surface interaction. Nevertheless, microstructural differences in the materials have not yet been considered within this interaction. This leads to a generalization of the process that can result in the failure of industrial components. Therefore, the aim of this work is to study the microstructural influence of the ball-burnishing process from a tribological perspective. Thus, martensitic and austenitic stainless steels were evaluated in terms of friction and surface integrity. The results show that parameterizing the process according to the tool–surface interaction is critical since improvements depend on friction as a function of the availability of plastic deformation of the crystallographic structures.
29 December 2022 in Journal of Materials Research and Technology
The development of accurate methodologies for a thorough comprehension of the erosion phenomenon is a challenging and necessary task. This study entailed an exhaustive analysis, incorporating empirical data obtained from an experiment involving the impingement of a sand and water jet on a submerged stainless-steel plate and numerical simulations, employing the Oka Erosion model that was compilated in OpenFOAM. The primary focus of this study was to generate W-shaped profiles delineating the impingement zone, derived both from experimental observations and the developed numerical model. This comparative approach facilitated a robust evaluation of the model’s efficacy in replicating erosion patterns. The outcomes of this analysis revealed a concurrence between the experimental and simulated erosion contours, affirming the model’s proficiency in representing erosion phenomena. Nevertheless, a minor discrepancy was noted, characterized by a slight underestimation of erosion rate and thickness loss. Furthermore, the investigation unveiled a noteworthy time-dependent trend in mass loss from the experimental data denoting a pseudo stabilization of the erosion rate across the time. This research contributes to the refinement of erosion modeling parameters and underscores the nature of time-dependent erosion behavior, a pivotal consideration for optimizing material durability.
This study presents the experimental validation of a remote sensing method for river flow velocity measurement, from which discharge is calculated, using Particle Image Velocimetry (PIV) combined with Unmanned Aerial Vehicles (UAVs). The case study focuses on the Antisana River in the Ecuadorian Andes, a region with challenging geography where accurate flow measurement is crucial for hydroelectric projects. The validation results demonstrate that the velocity measurements obtained through PIV closely align with those from standardized traditional methods. Furthermore, integrating technologies such as LiDAR for cross-sectional measurements, along with UAVs, would enable the accurate estimation of discharge in difficult-to-access areas. This approach has the potential to significantly enhance hydrological studies and water resource management in remote regions, especially for hydroelectric projects in the Ecuadorian Andes.
This study investigates the feasibility of utilizing surplus hydropower from Ecuador’s major hydroelectric plants to produce green hydrogen, a clean energy source that can be used to meet a large percentage of energy needs. Given Ecuador’s significant hydropower infrastructure, this approach leverages untapped energy resources for hydrogen production, with potential impacts on decarbonization strategies. A Pareto analysis identified five key hydroelectric plants that contribute the most to the national surplus. Using historical data from 2019 to 2023, a stochastic model was applied to estimate future surplus availability through 2030. The findings indicate that although Ecuador’s surplus hydropower peaked in 2021, the general trend shows a decline, suggesting an urgent need to capitalize on these resources efficiently. The results indicate a projected annual surplus of hydroelectric energy in Ecuador, ranging from 7475 to 3445 GWh over the next five years, which could be utilized for green hydrogen production. Ecuador thus has promising potential to become a green hydrogen producer, enhancing both regional energy security and carbon reduction goals. The reduction in energy availability for hydrogen production is attributed to the increasing energy demand and variable climatic conditions.
Wire arc additive manufacturing (WAAM) demands aluminum feedstock with tightly controlled diameter and high surface integrity. Adding hard TiC nanoparticles is a viable route to enhance the mechanical response of Al wires, yet the associated increase in contact severity can accelerate the wear of wire processing tools, particularly cemented carbide dies. This study elucidates the unidirectional sliding interaction between a TiC reinforced Al WAAM wire, and a WC/Co die material containing 5 wt% Co, using a modified scratch testing configuration under dry and lubricated conditions. Two dominant mechanisms are identified: (i) aluminum adhesion on the die surface and (ii) third body abrasion arising from WC particle pull out, promoted by preferential degradation of the cobalt binder. The presence of TiC nanoparticles reduces both the extent of Al transfer and the intensity of third body abrasion, an effect that is further amplified by lubrication. Consistently, lubrication also diminishes surface defects on the wire after sliding. The results provide a mechanistic basis to balance wire strengthening with tool life and highlight practical levers—nanoparticle reinforcement and lubrication strategies—for mitigating die damage while preserving WAAM wire surface quality.