The main objective of the study was to estimate the mean horizontal wind action on a façade scaffolding on the basis of full-scale data. Measurements of climatic parameters were carried out for a number of façade scaffoldings (120 structures) located in Poland over a 30-month period. The measurement points were located on 2–3 deck levels of each structure and at 2–4 points placed in each level. The measurements were carried out 3–4 times during each day for 5 consecutive days. At each point, two components of wind speed were measured: first with the vane probe directed perpendicular to the façade and then parallel to the façade. Each measurement lasted 60 s, and the data were recorded every 1 s. On the basis of wind speeds, a procedure was suggested that enabled estimation of the static wind action on façade scaffoldings. The responses of structures to this action were computed via FEM simulations. The results were compared with those based on the approaches recommended by the wind and scaffolding codes. Initial analyses, illustrated by three scaffoldings without a protective cover, indicated large discrepancies between the approaches and the possibility of wind action, which is not considered in the codes.

A system designed for making field measurements of wind action on engineering structures is described. The system is composed of sonic anemometers, differential pressure sensors, a barometer, and a thermohygrometer. The focus of this study is to determine the indications of sonic anemometers; to accomplish this goal, wind tunnel tests were performed. The tests did not involve checking the accuracy of the devices themselves, but determining their indications under field measurement conditions where certain unavoidable errors resulting from their installation can appear. The anemometer measurement uncertainty with respect to wind speed and angle was determined. The devices were rotated in a horizontal plane and inclined against and with the mean wind speed direction in a wind tunnel. Different tunnel wind speeds were tested. The results indicate stable device readings at different horizontal plane positions at different wind speeds and a low sensitivity to changes in inclination against the inflow.

The purpose of this paper is to show the influence of incorrect scaffolding foundations on the stress in their elements. Static stress analysis was performed for exemplary steel façade scaffolding. The scaffolding was formed using the Plettac 70 system and was composed of 16 modules and 13 working levels. The total dimensions of the scaffolding were 45.0 × 26.36 × 0.74 m. The scaffolding was set up partly on concrete and partly on a created ground classified as coarse sand with discontinuous graining. The boundary conditions modelling the foundation considered the heterogeneity of the ground both along the scaffolding and in the direction perpendicular to the façade. The effect of uneven subsidence on the scaffolding frames was checked, adopting a constant stiffness of 3500 kN/m in half of the supports, while in the rest of them the stiffness varied from 35 to 3500 kN/m. Due to additional bending moments, normal stresses in stands and transoms of the frames increased. Incorrect scaffolding foundation has the greatest negative effect on normal forces in anchors and bracings. Because these elements are responsible for the stability of the scaffolding, their damage may result in scaffolding failure and would certainly lead to a reduction of the values of free vibration frequencies, thus resulting in the discomfort of the workers on the scaffolding and a lack of safety.

This paper concerns an approach to model the ledger-stand joints of modular scaffolds. Based on the analysis of the working range of the ledger (represented by a linear relationship between load and displacement), two models of the ledger-stand joint are analysed: first - with flexibility joints and second - with rigid joints and with a transition part of lower stiffness. Parameters are selected based on displacement measurements and numerical analyses of joints, then they are verified. On the basis of performed research, it can be stated that both methods of joint modelling recommended in this paper, can be applied in engineering practices.

The paper presents an approach to evaluation of the dynamic wind action on scaffolding structures. FEM model of the scaffolding was created on the basis of geodetic measurements and verified by in-situ dynamic measurements of vibrations. Wind field, random in space and time, was simulated using Weighted Amplitude Wave Superposition (WAWS) method. Wind forces were applied to the nodes of the FEM model in every connection between stands and decks in outer plane of the scaffolding. Direct integration was used as the solution method. The time-dependent response of the structures was determined. Maximum response of the scaffolding was compared with results calculated according to the code recommendations.