The purpose of this paper is to show the influence of incorrect scaffolding foundations on the stress in their elements. Static stress analysis was performed for exemplary steel façade scaffolding. The scaffolding was formed using the Plettac 70 system and was composed of 16 modules and 13 working levels. The total dimensions of the scaffolding were 45.0 × 26.36 × 0.74 m. The scaffolding was set up partly on concrete and partly on a created ground classified as coarse sand with discontinuous graining. The boundary conditions modelling the foundation considered the heterogeneity of the ground both along the scaffolding and in the direction perpendicular to the façade. The effect of uneven subsidence on the scaffolding frames was checked, adopting a constant stiffness of 3500 kN/m in half of the supports, while in the rest of them the stiffness varied from 35 to 3500 kN/m. Due to additional bending moments, normal stresses in stands and transoms of the frames increased. Incorrect scaffolding foundation has the greatest negative effect on normal forces in anchors and bracings. Because these elements are responsible for the stability of the scaffolding, their damage may result in scaffolding failure and would certainly lead to a reduction of the values of free vibration frequencies, thus resulting in the discomfort of the workers on the scaffolding and a lack of safety.

The analyzes and classifications presented in the article were based on the research carried out in the years 2016 to 2018 on a group of over one hundred scaffoldings assembled and used on construction sites in different parts of Poland. During scaffolding selection process efforts were made to maintain diversification in terms of parameters such as scaffolding size, investment size, type of investment, location and nature of conducted 5works. This resulted in the research being carried out on scaffoldings used for church renovation in a small town or attached to the facades of classic apartment blocks, as well as on scaffoldings used during construction of skyscrapers or facilities of the largest power plants. This variety allows to formulate general conclusions about the technical condition of used frame scaffoldings. Exploitation damages of the frame scaffolding elements were divided into three groups. The first group includes damages to the main structural components, which reduce the strength of the scaffolding elements and hence the whole structure. The qualitative analysis of these damages was made based on numerical models that take into account the geometry of the damage and based on computational nonlinear static analyzes. The second group focuses on exploitation damages such as the lack of a pin on the guardrail bolt which may cause an imminent threat to people using scaffolding. These are local damages that do not affect the bearing capacity and stability of the whole structure but are very important for safe use. The last group consider damages that reduce only aesthetic values and do not have direct impact on bearing capacity and safety of use. Apart from qualitative analyzes the article will present quantitative analyzes showing how frequently given type of damage occurs.

The publication focuses on the issue of inventory surveying of façade scaffolding. The authors considered various land surveying methods such as photogrammetry, laser scanning or total station. To test these methods, sample measurements were performed on the deployed scaffolding. Specific equipment was used: GOM Tritop system with invar scale patterns, Leica C20 scanner and Leica TS50 total station. The authors present arguments for and against mentioned methods and also an analysis of the measurements of 10 scaffoldings. Finally, as a leading method the total station was chosen. The results of the tests and analyses confirmed that the accuracy of the selected method is 3 mm for the width and 3.6 mm for the height of the frame. Research material was collected from April to November 2016, with the use of Leica TS50 total station (1cc, 1 mm + 1 ppm), by one surveying team.

This paper presents the problem of comparing the results of computer simulations with the results of laboratory tests. The subject of the study was the insert-type joint of scaffolding loaded with a bending moment. The research was carried out on the real elements of the scaffolding. Due to the complexity of the connection different friction coefficients and depths of wedge insertion were taken into account in the analysis. The aim of conducting the series of analyses was to determine the sensitivity of the model to the mentioned characteristics. Since laboratory tests were carried out on the real samples, there were no preparations of surface involved in the load transfer. This approach caused many problems with the clear definition of the nature of work of individual node elements during the load. The analysis consist of two stages: the stage in which the connection is defined (the wedge is inserted into the rosette), and the loading stage (the node is loaded by the bending moment).