The goal of the paper is to study the charge transfer and reactions at the columbite-(Fe) (FeNb2O6) mineral surface during the HF leaching process. In this paper, X-ray photoelectron spectroscopy (XPS), leaching experiments, and density functional theory (DFT) calculations were used to study the surface element adsorption, charge distribution, chemical state, and energy changes of the mineral surface during the process of leaching columbite–(Fe) with different concentrations of hydrofluoric acid. The results showed that as the concentration of F atoms was increased during the acid leaching process, the Nb–O bond was more likely to be broken than the Fe–O bond; the amount of charge transferred from Nb atom to F atom (0.78 e–0.94 e/atom) was greater than that from Fe atom to the F atom (0.25 e–0.28 e/atom), so it was determined that compared to Fe atoms, it was easier for the Nb atoms to bind to F. The results of XPS analysis showed that the electron binding energies of Nb5+–O, Fe3+–O, and Fe2+–O bonds on the mineral surface increased sequentially, and the M–O bond broke during the acid leaching process, forming more stable M–F bonds. Therefore, the Nb5+–F bonds were easier to form a stable structure. Combined with the ICP results, it was found that in the filtrate after 5M HF and 10M HF acid leaching minerals, c(Nb)/c(Fe) were 2.69 and 2.95, respectively, and the concentration ratio of Nb to Fe element in the mineral was 2 which was lower than 2.69 and 2.95, confirming the result of DFT calculation and illustrating that Nb atoms in columbite-(Fe) mineral were more soluble than Fe atoms.
This study explores the effect of introducing additional alloy elements not only in a different order but also at different stages of the Ruhrstahl-Heraeus (RH) process of low-carbon silicon steel production. A more economical method, described as “pre-alloying”, has been introduced. The evolution of MnO-FeO inclusions produced by pre-alloying was investigated. Results show that spherical 3FeO·MnO inclusions form first, then shelled FeO·zMnO (z = 0.7–4) inclusions nucleate on the surface of pre-existing 3FeO·MnO. Spherical FeO·zMnO (z = 3–5) is further evolved from shelled 3FeO·MnO by diffusion. Because these MnO-FeO inclusions float up into the slag before degassing, the pre-alloying process does not affect the quality of the melt in the end. Both carbon content and inclusion size conform to industry standards.
Scalable production of large size and high quality graphene is an important prerequisite to fully realize its commercial applications. Herein, we propose a high-efficient route for preparing few-layer graphene. The secondary exfoliation of unexfoliated graphite flakes from electrochemical exfoliation was achieved by using ultrasonication assisted microwave exfoliation technique. The results show that the as-prepared sample has a C/O of 15.2, a thickness of about 1 nm and a transverse dimension of over 100 nm, and the Raman spectrogram shows low defects upon reduction of the sample. These results suggest that electrolytic graphene can be exfoliated to form graphene nanosheets under ultrasonic-assisted microwave technology, thus indicating that the current method has great potential for synthesizing high-quality graphene at an industrial-scale.
Surface hardening improves the strength of low-carbon steel without interfering with the toughness of its core. In this study, we focused on the microstructure in the surface layer (0–200 μm) of our low-carbon steel, where we discovered an unexpectedly high level of hardness. We confirmed the presence of not only upper bainite and acicular ferrite but also lath martensite in the hard surface layer. In area of 0–50 μm, a mixed microstructure of lath martensite and B1 upper bainite was formed as a result of high cooling rate (about 50–100 K/s). In area of 50–200 μm, a mixed microstructure of acicular ferrite and B2 upper bainite was formed. The average nanohardness of the martensite was as high as 9.87 ± 0.51 GPa, which was equivalent to the level reported for steel with twenty times the carbon content. The ultrafine laths with an average width of 128 nm was considered to be a key cause of high nanohardness. The average nanohardness of the ferrites was much lower than for martensite: 4.18 ± 0.39 GPa for upper bainite and 2.93 ± 0.30 GPa for acicular ferrite. Yield strength, likewise, was much higher for martensite (2378 ± 123 MPa) than for upper bainite (1007 ± 94 MPa) or acicular ferrite (706 ± 72 MPa). The high yield strength value of martensite gave the surface layer an exceptional resistance to abrasion to a degree that would be unachievable without additional heat treatment in other steels with similar carbon content.