Besides a wide application in corrosion protection, wear resistance increase, providing thermal properties and power conversion, oxide coatings have found an alternative application in welding technology as catalysts of the tungsten inert gas (TIG) welding process. In this paper, the novel approach of fabricating a coating containing nanoparticles based on nanosized SiO₂ and TiO₂ and their mixtures was applied to the austenitic stainless-steel base metal. It was found that coatings increased depths of penetration, enabling a consumable-free welding. Using this method, the use of several critical and near-critical raw materials (e.g., Si and Cr), as well as the relatively expensive Ni can be completely avoided. The most effective coating in terms of weld penetration consisted of a mixture of nanoparticles, rather than unary oxide coatings based on nanoparticles. A model for liquid weld metal flow is proposed based on the metallographic examination of recrystallized grains and microhardnesses measured near the weld metal, supporting the reversed Marangoni convection theory.

The paper presents the influence of the activation flux and shielding gas on tungsten inert gas (A-TIG) welding of the stainless steel. In introduction part, duplex stainless steel was analysed. The A-TIG process was explained and the possibility of welding stainless steels using the A-TIG process to maximize productivity and the cost-effectiveness of welded structures was presented. In the experimental part duplex, 7 mm thick stainless steel has been welded in butt joint. The influence of activation flux chemical composition upon the weld penetration has been investigated prior the welding. The welding process was performed by a robot with TIG equipment. With selected A-TIG welding technology preparation of plates and consumption of filler material (containing Cr, Ni and Mn) have been avoided. Specimens sectioned from the produced welds have been subjected to tensile strength test, macrostructure analysis and corrosion resistance analysis. The results have confirmed that this type of stainless steel can be welded without edge preparation and addition of filler material containing critical raw materials as Cr, Ni and Mn when the following welding parameters are set: current 200 A, welding speed 9,1 cm/min, heat input 1,2 kJ/mm and specific activation flux is used.

This study explores an innovative method to enhance Directed Energy Deposition (DED) of aluminum 5356 products by integrating an electromagnetic vibration system into the DED setup. The application of vibrations significantly improved surface quality, reducing surface waviness and increasing building efficiency by 14%, from 78.5% to 92.25%.Gas porosity was reduced from 1.5 ± 0.04% in as-built (AB) components to 0.34 ± 0.07% in vibration-assisted (VA) parts. Tensile tests showed a marked reduction in anisotropy, with the tensile strength deviation between the x and z directions decreasing to less than 0.4% for vibration-assisted samples, compared to 7.9% for asbuilt ones. Additionally, secondary phase analysis revealed a homogenization effect, with magnesium- and iron-rich precipitates displaying a finer dispersion (3.57 ± 3.42 µm²) compared to 11.28 ± 12.49 µm² in as-built parts. Overall, the findings highlight the potential of vibration-assisted DED to improve part properties, reduce defects, and advance the DED manufacturing process.

The paper presents a set of findings important for a Wire Arc Additive Manufacturing using a welding robot. At the beginning an overview of additive manufacturing technologies for production of metal parts is presented. A special attention is set to wire arc additive manufacturing (WAAM) technologies. The advantage of WAAM compared to laser or electron beam technologies are lower investment and operational costs, while the disadvantage could be a lower dimensional accuracy. Due to higher productivity the WAAM technologies are more suitable for production of bigger parts. In this paper results study of WAAM using a welding robot and a CMT power source is presented. Thin walls have been cladded using G3Si1 welding wire. The microstructure and hardness of produced structures were measured and analysed. A research was done to determine the optimal welding parameters for production of thin walls with smooth surface. A SprutCAM software was used to make a code for 3D printing of sample part. It was find out that weld interpass temperature and workpiece to contact tip length play an important role in WAAM technologies.