Markel Sanz

Mr. Markel Sanz

Dynamics & Control Department, Ideko, Elgoibar, 20870 Basque Country, Spain;
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 September 2024 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Open access
MSMarkel Sanz
Markel Sanz
AIAlex Iglesias
Alex Iglesias
LLL.N. López de Lacalle
L.N. López de Lacalle
ZDZ. Dombovari
Z. Dombovari
JMJ. Munoa
J. Munoa

25 February 2025 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Open access
DHDavid Hajdu
David Hajdu
OFOier Franco
Oier Franco
MSMarkel Sanz
Markel Sanz
Giovanni TotisGiovanni Totis
Giovanni Totis
JMJokin Munoa
Jokin Munoa
ZDZoltan Dombovari
Zoltan Dombovari

1 March 2023 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Open access
MSMarkel Sanz
Markel Sanz
JMJ. Munoa
J. Munoa
AIA. Iglesias
A. Iglesias
Luis Norberto López De LacalleLuis Norberto López De Lacalle
Luis Norberto López De Lacalle
ZDZ. Dombovari
Z. Dombovari

13 March 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MSMarkel Sanz
Markel Sanz
ZDZoltan Dombovari
Zoltan Dombovari
JMJokin Munoa
Jokin Munoa
AIAlex Iglesias
Alex Iglesias
Luis Norberto López De LacalleLuis Norberto López De Lacalle
Luis Norberto López De Lacalle
The production and repair of blades for aerospace engines and energy turbines is a complex process due their inherently low stiffness and damping properties. The final recontouring operation is usually performed by milling operations where regenerative chatter is one of the main productivity limiting factors. With the objective of avoiding specific stiffening fixtures for each blade geometry, this paper proposes a semi-active tuneable clamping table (TCT) based on mode tuning for blade machining. The active mode of the device can be externally controlled by means of a rotary spring and eddy current damping modules. Its in-series architecture allows damping to be introduced to the critical mode of the thin-walled part without any direct contact in the machining area and enables a more universal clamping. Its chatter suppression capabilities are maximized by means of a novel self-tuning algorithm that iteratively optimizes the tuning for the measured chatter frequency. The benefits of the iterative algorithm are validated through semidiscretization and initial value time-domain simulations, showing a clear improvement in blade recontouring stability compared to regular broad-bandwidth tuning methods.

23 January 2024 in CIRP Journal of Manufacturing Science and Technology
Verified
Journal Article
Open access
MSMarkel Sanz
Markel Sanz
JMJokin Munoa
Jokin Munoa
Lorenzo MorelliLorenzo Morelli
Lorenzo Morelli
AIAlex Iglesias
Alex Iglesias
Luis Norberto López De LacalleLuis Norberto López De Lacalle
Luis Norberto López De Lacalle
ZDZoltan Dombovari
Zoltan Dombovari

8 May 2020 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
MSMarkel Sanz
Markel Sanz
AIAlex Iglesias
Alex Iglesias
JMJokin Munoa
Jokin Munoa
ZDZoltan Dombovari
Zoltan Dombovari
Two different kinds of descriptions for edge geometry of harmonically varied helix tools are studied in this work. The edge geometries of the so-called lag and helix variations are used in this paper, and their equivalency is established from engineering point of view. The equivalent relation is derived analytically and the nonlinear algebraic system is described, with which the numerical equivalency properties can be determined. The equivalent description can be utilized in variable helix tool production to determine an optimized set of geometrical parameters of the edge geometry. The stability properties are shown and compared for a simple one degree-of-freedom case with the nonuniform constant helix tools. The robustness of the results related to the harmonically varied tools is critically discussed in this paper showing advantages compared to the nonuniform constant helix case. The results suggest that the more extreme the edge variation is, the more stable the process performed with the corresponding harmonically varied tool becomes.