Several natural materials and vegetable waste have relevant mechanical properties, mainly in its fiber format. Particularly, banana fiber (BF) provides a close behavior to the widely spread glass fibers, which places it in an advantageous position for use as a reinforcing material in plastic composites. This work characterizes the behavior of acrylonitrile butadiene styrene (ABS), high impact polystyrene (HIPS), and high density polyethylene (HDPE) reinforced with short fibers of bananas from the Canary Islands for its application in molding processes. Several thermal analyses (Thermal Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), and Melt Flow Index (MFI)) and mechanical tests (tensile, flexural, impact, and Dynamic Mechanical Analysis (DMA)) were carried out in composites with different percentages of banana fiber. The thermal results show that the use of banana fiber is viable as a reinforcement in composites for injection molding processes and the mechanical tests indicate an increase in stiffness and an improvement in maximum flexural stress by increasing the fiber content in composites, so the banana fiber turns out to be a natural alternative for the reinforcement of injected plastic components.

Bags used to protect and accelerate the ripening of bananas are a clear example of the environmental problem of packaging waste. Small pieces of these non-biodegradable bags are frequently disposed on the soil by accident (environmental conditions and poor handling during the harvest) and remain there for years. This work focuses on the development of protective biodegradable bags reinforced with banana fiber, obtained from waste of the banana plants, thus promoting a circular economy and a more environmentally friendly process. To achieve this, different bio-based composites were tested (processability) by compounding extrusion (biopolymer and banana fiber with different process steps) and blown film extrusion. The bags produced were tested in field and sequentially improved in three generations of biofilms. The results showed that the maximum processable fiber content was 5 wt %. Additionally, the micronizing of the compounds was crucial to simplify the blown film extrusion and improve the smoothness of the bags (scratches avoidance on the banana surface). The final bags (Mater-Bi biopolymer, 5% combed and sieved banana fiber, and 2.5 wt % TiO₂ for ultraviolet light filtration), performed better than the conventional ones (faster maturing, i.e., earlier harvest, and easier handling) and fulfilled the biodegradability, composting and ecotoxicity test requirements.

The incorporation of ceramic additives is the most commonly used strategy to improve the biofunctionality of polymer-based scaffolds intended for bone regeneration. By embedding ceramic particles as a coating, the functionality improvement in the polymeric scaffolds can be concentrated on the cell–surface interface, thus creating a more favourable environment for the adhesion and proliferation of osteoblastic cells. In this work, a pressure-assisted and heat-induced method to coat polylactic acid (PLA) scaffolds with calcium carbonate (CaCO₃) particles is presented for the first time. The coated scaffolds were evaluated by optical microscopy observations, a scanning electron microscopy analysis, water contact angle measurements, compression testing, and an enzymatic degradation study. The ceramic particles were evenly distributed, covered more than 60% of the surface, and represented around 7% of the coated scaffold weight. A strong bonding interface was achieved, and the thin layer of CaCO₃ (~20 µm) provided a significant increase in the mechanical properties (with a compression modulus improvement up to 14%) while also enhancing the surface roughness and hydrophilicity. The results of the degradation study confirmed that the coated scaffolds were able to maintain the pH of the media during the test (~7.6 ± 0.1), in contrast to the pure PLA scaffolds, for which a value of 5.07 ± 0.1 was obtained. The ceramic-coated scaffolds developed showed potential for further evaluations in bone tissue engineering applications.

Outdoor and indoor atmospheric pollution is one of the major problems that humanity continues to face. As a mitigation pathway, numerous technologies have been developed for air purification, including the use of fibrous filters. In this study, the particle capture efficiencies and pressure drops of air filters manufactured with cellulose pulp extracted from banana pseudostems were studied across three particle size ranges (PM10, PM2.5, and PM1). Two pretreatments were applied, alkaline with soda-antraquinone (alkali-treated pulp) and a subsequent bleaching process (bleached pulp), and four manufacturing processes were tested: crushing, freeze-drying, vacuum filtration, and pressing. In addition, a study varying filter grammage (70, 100, and 160 g·m⁻²) and pressing pressures (2, 4, 6, and 8 t) was also performed. After conducting these particle tests, the filter manufactured with bleached pulp, having a grammage of 160 g·m⁻² and pressed at 4 t, was deemed the optimal individual solution. It demonstrated high particle retention efficiencies across all particle size ranges (with values exceeding 80%), a moderate pressure drop below 1000 Pa, and high thermal stability (degradation above 220 °C). However, combining freeze-drying and two-ton pressing processes yielded improved results (83% for the smallest particles and 89% for others) with approximately half the pressure drop. Based on these results, this study stands as a noteworthy contribution to waste valorization and the advancement of environmentally friendly materials for particle air filters. This is achieved through the adoption of simple and cost-effective technology, coupled with the utilization of 100% natural agricultural waste as the primary manufacturing material.

The combination of Atomic Diffusion Additive Manufacturing (ADAM) and traditional CNC machining allows manufacturers to leverage the advantages of both technologies in the production of functional metal parts. This study presents the methodological development of hybrid manufacturing for solid copper parts, initially produced using ADAM technology and subsequently machined using a 5-axis CNC system. The ADAM technology was dimensionally characterized by adapting and manufacturing the seven types of test artifacts standardized by ISO/ASTM 52902:2019. The results showed that slender geometries suffered warpage and detachment during sintering despite complying with the design guidelines. ADAM technology undersizes cylinders and oversizes circular holes and linear lengths. In terms of roughness, the lowest results were obtained for horizontal flat surfaces, while 15° inclined surfaces exhibited the highest roughness due to the stair-stepping effect. The dimensional deviation results for each type of geometry were used to determine the specific and global oversize factors necessary to compensate for major dimensional defects. This also involved generating appropriate over-thicknesses for subsequent CNC machining. The experimental validation of this process, conducted on a validation part, demonstrated final deviations lower than 0.5% with respect to the desired final part, affirming the feasibility of achieving copper parts with a high degree of dimensional accuracy through the hybridization of ADAM and CNC machining technologies.