In this paper, wool carpet dye adsorption properties of nanoporous activated carbon materials (NCMs) prepared from bamboo agro-product is reported. Bamboo cane powder was chemically activated with phosphoric acid at different temperatures (400, 500, and 600 °C) at an impregnation ratio of 1:1. We found that the specific surface area and the total pore volume of NCM increases with temperature giving the highest surface area and pore volume ca. 2130 m2·g−1 and 2.69 cc·g−1 at 600 °C. Owing to superior surface textural properties, bamboo-derived NCM showed excellent adsorption capacity for wool carpet dyes Lanasyn orange (LO) and Lanasyn gray (LG). The adsorption phenomena could be described by Langmuir/Freundlich adsorption isotherm models. The maximum adsorption capacity was ca. 2.60 × 103 and 3.04 × 103 mg·g−1 for LO and LG, respectively. The adsorption followed pseudo second order kinetics with the second order rate constant of 1.24 × 10−3 g·mg−1·min−1 (LO) and 7.69 × 10−4 g·mg−1·min−1 (LG), respectively. This study demonstrated that the high surface area NCMs prepared from agro-product can be used as efficient and cost-effective adsorbent materials for the removal of dyes from industrial effluent.
The electrical double-layer supercapacitance performance of the nanoporous carbons prepared from the Phyllanthus emblica (Amala) seed by chemical activation using the potassium hydroxide (KOH) activator is reported. KOH activation was carried out at different temperatures (700–1000 °C) under nitrogen gas atmosphere, and in a three-electrode cell set-up the electrochemical measurements were performed in an aqueous 1 M sulfuric acid (H2SO4) solution. Because of the hierarchical pore structures with well-defined micro- and mesopores, Phyllanthus emblica seed-derived carbon materials exhibit high specific surface areas in the range of 1360 to 1946 m2 g−1, and the total pore volumes range from 0.664 to 1.328 cm3 g−1. The sample with the best surface area performed admirably as the supercapacitor electrode-material, achieving a high specific capacitance of 272 F g−1 at 1 A g−1. Furthermore, it sustained 60% capacitance at a high current density of 50 A g−1, followed by a remarkably long cycle-life of 98% after 10,000 subsequent charging/discharging cycles, demonstrating the electrode’s excellent rate-capability. These results show that the Phyllanthus emblica seed would have significant possibilities as a sustainable carbon-source for the preparing high-surface-area activated-carbons desired in high-energy-storage supercapacitors.
High-surface-area porous carbon materials with high porosity and well-defined pore structures are the preferred advanced supercapacitors electrode materials. Here, we report the electrochemical supercapacitive performance of novel high-porosity activated carbon materials prepared from biowaste Terminalia chebula (Harro) seed stones involving zinc chloride (ZnCl2) activation. Activation is achieved by mixing ZnCl2 with Harro seed powder (1:1 w/w) followed by carbonization at 400–700 °C under a nitrogen gas atmosphere. The amorphous carbon materials obtained exhibit excellent performance as electrical double-layer capacitor electrodes in aqueous electrolyte (1 M sulfuric acid) due to high specific surface areas (as high as 1382.6 m2 g−1) based on well-developed micropore and mesopore structures, and partial graphitic structure containing oxygenated surface functional groups. An electrode prepared using material having the optimal surface textural properties achieved a large specific capacitance of 328.6 F g−1 at 1 A g−1 in a three-electrode cell setup. The electrode achieved a good capacitance retention of 44.7% at a high 50 A g−1 current density and outstanding cycling performance of 98.2% even following 10,000 successive charge/discharge cycles. Electrochemical data indicate the significant potential of Terminalia chebula seed-derived porous carbons as high-performance electrode materials for high-energy-storage supercapacitor applications.
Accurate measurement of the microspores, mesopores, and macropores on the surface of the activated carbon is essential due to its direct influence on the material’s adsorption capacity, surface area, and overall performance in various applications like water purification, air filtration, and gas separation. Traditionally, Scanning Electron Microscopy (SEM) images of activated carbons are collected and manually annotated by a human expert to differentiate and measure different pores in the surface. However, manual analysis of such surfaces is costly, time-consuming, and resource-intensive as requires supervision from experts. In this paper, we propose an automatic Deep-learning-based solution to address this challenge of activated carbon surface segmentation. We introduce a novel SEM Image segmentation dataset for activated carbon. We then evaluate the state-of-the-art deep learning models on the novel semantic segmentation task that shows promising results. Finally, we outline the key research challenges and discuss potential research directions to address these challenges.
31 December 2019 in Journal of Nepal Chemical Society
Water quality parameterization is a great concern because chemical contaminants and microbiological impurities including pathogenic bacteria may pose a health risk and unfit for its domestic use. Alkalinity, pH, conductivity, chlorine demand, turbidity, and ammonia were measured to characterize the water quality of the Bagmati River. The effect of tributaries on Bagmati River was determined by sampling water from five different sites such as Pashupati (B-1), Shankhamul (B-2), Kupondol (B-1), Balkhu (B-4), and Jalbinayek (B-5) sites. The water samples B-2, B-3, B-4 and B-5 were less turbid but black in color while water sample B-1 was more turbid but grey in color. The pH of water samples ranged from 6.7 to 7.3. The alkalinity, conductivity and chlorine demand were 60 ppm, 95.7 µs and, 5.44 ppm, respectively for B-1 sample and increased almost continuously from B-2 to B-5 sample. The alkalinity was 360 ppm, conductivity was 862 µs and chlorine demand was 23.7 ppm for the last sample (B-5). The concentration of ammonia in the B-1 sample was only 0.0625 ppm whereas it was 3.32 ppm in the B-5 sample. The enhancement of chlorine demand and concentration of ammonia attributed that tributary and local effluent loaded extremely high levels of pollutants into the Bagmati River which might include pathogenic microorganisms. The random chance of some parameters like pH, conductivity, ammonia, turbidity along the Bagmati River indicates the impacts of different tributaries on Bagmati River. The chorine demand showed a positive correlation with conductivity, alkalinity and ammonia while the negative correlation with turbidity. This revealed that the conductive alkaline pollutants consumed more chlorine than colloidal particles. From the study it is considered that the Bagmati River water contains natural as well as anthropogenic pollutants which is extremely hazardous not only to the people using river water but also for the living organism rely on the river.