Climate targets set by the EU, including the reduction of CO2, are leading to the increased use of lightweight materials for mass production such as press hardening steels. Besides sheet metal forming for high-strength components, tubular or profile forming (Hot Metal Gas Forming—HMGF) allows for designs that are more complex in combination with a lower weight. This paper particularly examines the application of conductive heating of the component for the combined press hardening process. The previous Finite-Element-Method (FEM)-supported design of an industry-oriented, curved component geometry allows the development of forming tools and process peripherals with a high degree of reliability. This work comprises a description regarding the functionality of the tools and the heating strategy for the curved component as well as the measurement technology used to investigate the heat distribution in the component during the conduction process. Subsequently, forming tests are carried out, material characterization is performed by hardness measurements in relevant areas of the component, and the FEM simulation is validated by comparing the resulting sheet thickness distribution to the experimental one.
Within the framework of investigations, an exhaust gas component made of Titanium Grade 2 was produced by means of Hot Metal Gas Forming (HMGF) at the Fraunhofer IWU in Chemnitz, Germany. The semi-finished products were two-fold bent, thermal joined, calibrated and pre-formed tubes. So far, a three-stage internal high-pressure forming process at room temperature plus two necessary intermediate heat treatments were used to produce the component. Due to its complexity as well as the limited forming ability of Titanium Grade 2 at room temperature an one step Hot Metal Gas Forming was developed to replace the former procedure.
Sheet metal parts can often replace milled components, strongly improving the buy-to-fly ratio in the aeronautical sector. However, the sheet metal forming of complex parts traditionally requires expensive tooling, which is usually prohibitive for low manufacturing rates. To achieve precise parts, non-productive and cost-intensive geometry straightening processes are additionally often required after forming. Rollforming is a possible technology for producing profiles at large rates. For low manufacturing rates, robotic rollforming can be an interesting option, significantly reducing investment at the cost of higher manufacturing times while keeping a high process flexibility. Forming is performed incrementally by a single roller set moved by the robot along predefined bending curves. The present work’s contribution to the overall solution is the development of an intelligent algorithm to calculate geometry after a robotic rollforming process based on process reaction forces. This information is required for in-process geometric distortion correction. Reaction forces and torques are acquired during the process, and geometry is calculated based on artificial intelligence (AI) applied to that information. The present paper describes the AI development for this virtual geometry sensing system.
This paper presents a novel approach of a smart shortened material loop for producing second-life metallic components by saving a significant amount of energy and CO2 emissions. The focus is on metallic components and manufacturing chains based on adapted forming technologies. Sourcing and using secondary semi-finished products instead of virgin metallic materials facilitates the omission of process steps, such as iron smelting, steel making, continuous casting, hot and cold rolling, which involve the highest energy consumption and the highest CO2 emissions. Besides the positive impacts on sustainability, there are still scientific and technological challenges. One challenge lies in matching providers of secondary semi-finished material to market needs; the other comprises engineering the forming process chain while some material characteristics are not clearly specified or vary in a wide range. In contrast to the heavily restricted properties of virgin material, the characteristics of secondary semi-finished materials vary in a wider range and need to be elaborated. In the end, a new component will be produced, differing in design, function, and properties from conventional, single-life cycle products. Therefore, this paper introduces a novel, circular material loop for metals. The paper finishes with a short concept note on digital material and product passports to store and provide the required information on properties.
To reduce weight of a component and improve its performance, the part properties have to be adapted to the requirements, the load profile, and the function of the product. This leads to a continuously increasing complexity of the components necessitating innovative manufacturing strategies for producing the desired shapes from materials that are difficult to handle. Hydroforming offers high potential for fulfilling this demand, especially, if it is applied in deliberate process integrations, combinations, and chains that allow exploiting complementary advantages of all technologies involved. The paper presents four examples of such manufacturing strategies: magnetic pulse welding followed by tube hydroforming, deep drawing combined with injection moulding and hydroforming using the molten plastic, free bending or roll forming followed by hydroforming, and deep drawing with integrated media forming.