Karsten Richter

Mr. Karsten Richter

Fraunhofer Institute for Machine Tools and Forming Technology, Chemnitz, Saxony, Germany
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 February 2023 in Robotics
Verified
Journal Article
Open access
PDF file
TATina Abdolmohammadi
Tina Abdolmohammadi
VRValentin Richter-Trummer
Valentin Richter-Trummer
AAAntje Ahrens
Antje Ahrens
KRKarsten Richter
Karsten Richter
AAAlaa Alibrahim
Alaa Alibrahim
MWMarkus Werner
Markus Werner
Sheet metal parts can often replace milled components, strongly improving the buy-to-fly ratio in the aeronautical sector. However, the sheet metal forming of complex parts traditionally requires expensive tooling, which is usually prohibitive for low manufacturing rates. To achieve precise parts, non-productive and cost-intensive geometry straightening processes are additionally often required after forming. Rollforming is a possible technology for producing profiles at large rates. For low manufacturing rates, robotic rollforming can be an interesting option, significantly reducing investment at the cost of higher manufacturing times while keeping a high process flexibility. Forming is performed incrementally by a single roller set moved by the robot along predefined bending curves. The present work’s contribution to the overall solution is the development of an intelligent algorithm to calculate geometry after a robotic rollforming process based on process reaction forces. This information is required for in-process geometric distortion correction. Reaction forces and torques are acquired during the process, and geometry is calculated based on artificial intelligence (AI) applied to that information. The present paper describes the AI development for this virtual geometry sensing system.

1 March 2018 in Materials Science Forum
Verified
Journal Article
Open access
PDF file
KRKarsten Richter
Karsten Richter
FRFranz Reuther
Franz Reuther
RMRoland Müller
Roland Müller
DLDirk Landgrebe
Dirk Landgrebe
The spring industry has to process ultra-high strength spring strips of the steel grade 1.4310 (X10CrNi18-8). Springback during bending is a limiting factor for a resource-efficient production process in the so called stamping bending technology. This paper reports a mainly experimental investigation on the influence of bending parameters on the evolving springback of spring strips of the grade 1.4310 with tensile strengths TS = 1500-1800 MPa.

8 December 2015 in Acta Metallurgica Sinica (English Letters)
Verified
Journal Article
Closed access
PDF file
KRKarsten Richter
Karsten Richter
RMRoland Müller
Roland Müller
AKAndreas Kunke
Andreas Kunke
VKVerena Kräusel
Verena Kräusel
DLDirk Landgrebe
Dirk Landgrebe

Verified
Journal Article
Open access
PDF file
SWSven Winter
Sven Winter
KRKarsten Richter
Karsten Richter
EGElmar Galiev
Elmar Galiev
MNMatthias Nestler
Matthias Nestler
Verena PsykVerena Psyk
Verena Psyk
VKVerena Kräusel
Verena Kräusel
Punching of ultra-high-strength spring steel causes critical stresses in the tools. Pronounced wear and even spontaneous failure may occur. Wear of the punches influences the quality of the cutting surfaces of the blanked parts, which is predominantly determined by the cutting edge radius. The radius differs with an increasing number of strokes depending on the punch material. However, there are no studies characterizing the influence of the cutting edge radius on the cutting surface quality on an industrial scale, i.e., considering a very high number of strokes. In the presented study, punches made of high-speed steel, powder metallurgical steel and carbide were used to punch the ultra-high-strength steel 1.4310 (Rm = 1824 MPa) up to 1,000,000 strokes. The experiments were stopped at defined number of strokes, the punches were removed, nondestructively characterized regarding cutting edge radius and wear and reinstalled. It turned out that the radius differed significantly over the number of strokes and, further, varied depending on the punch material. Remarkably, the most low-cost material, precisely the high-speed steel, showed the smallest cutting edge radius of 16 µm and brought the parts with the best cutting surface quality (more than 30% burnish zone) after the maximum number of strokes. The results indicate clearly that the cutting edge radius develops differently for each regarded material and at different number of strokes. Therefore, it is of utmost importance to perform wear tests on different numbers of strokes under industrial conditions. With the knowledge gained, it will be possible to design optimized punches with lower costs and increased lifetime.

1 January 2015 in Materials Today: Proceedings
Verified
Journal Article
Open access
KRKarsten Richter
Karsten Richter
RHR. Haase
R. Haase
FSF. Schieck
F. Schieck
DLD. Landgrebe
D. Landgrebe
The sheet metal forming of magnesium alloys requires an adaption of the forming processes utilized. Due to limited formability at room temperature, heating above a temperature of 200 to 225 °C is necessary in order to activate additional gliding planes. By the example of roll forming, the temperature regime and implementation of heating equipment into the forming process is illustrated. On account of the progressive feed of sheet material necessary for roll forming, a transverse flux induction heating was used in the experimental setup. Results of experimental design and experimentation with AZ31 alloy will be presented in this paper

20 March 2019 in Materials Science Forum
Verified
Journal Article
Open access
PDF file
KRKarsten Richter
Karsten Richter
FRFranz Reuther
Franz Reuther
RMRoland Müller
Roland Müller
One effect of high influence on the dimensional accuracy during bending is springback. It inevitably occurs due to the elastic proportion in the material behavior. The impact is notably high when producing springs made of ultra-high strength spring strips of the steel grade 1.4310 (X10CrNi18-8). The high yield ratio needed to fulfil the functionalities required during application leads to dimensional inaccuracies that have to be compensated during the production process. This paper reports a simulation-based approach to predict the springback behaviour of ultra-high strength spring strips with tensile strengths TS = 1500-1800 MPa. Based on the results of advanced material testing and modelling, the numerical prediction of the springback behavior of an exemplary bending process (free bending) has been investigated in detail. This helps to obtain deeper knowledge and understanding of the springback phenomenon and to achieve suitable strategies for a more efficient industrial tool and process design while processing ultra-high strength spring strips.