The estimation of forest biomass is gaining interest not only for calculating harvesting volumes but also for carbon storage estimation. However, bark (and carbon) compounds are not distributed equally along the stem. Particularly when looking at Scots pine, a radical change in the structure of the bark along the stem can be noted. At the bark transition area, the bark changes from thick and rough to thin and smooth. The aim of our study was (1) to analyze the height of the bark transition area where the bark structure changes and (2) to analyze the effect of cardinal direction on the bark thickness. Regression analyses and forward selection were performed including measured tree height, DBH, bark thickness, crown base height and upper and lower heights of the bark transition areas of 375 trees. While the cardinal direction had no effect on bark thickness, DBH was found to have a significant effect on the heights of the bark transition areas, with stand density and tree height having a minor additional effect. These variables can be used to estimate timber volume (without bark) with higher accuracy and to predict the carbon storage potential of forest biomass according to different tree compartments and compounds.

In terms of assessing economic impact, one of the most important elements in the wood supply chain is the measurement of round wood. Besides the one-by-one measurement of logs, logs are often measured when stacked at the forest road. The gross stacked volume includes the volume of the wood, bark and airspace and is widely used for industrial wood assortments. The increasing international attention given to photo-optical measurement systems for portable devices is due to their simplicity of use and efficiency. The aim of this study was to compare the gross volumes of hardwood log stacks measured using one widespread photo-optical app with two manual section-wise volume estimations of log stacks based on the German framework agreement for timber trade (RVR). The manual volume estimations were done starting from the left (RVR) and right (RVR) sides of the log stacks. The results showed an average deviation of the photo-optical gross volume estimation in comparison to the manual estimation of –2.09% (RVR) and –3.66% (RVR) while the deviation between RVR and RVR was +2.54%. However, the log stack gross volume had a highly significant effect on the deviation and better accuracy with smaller deviation were reached for larger log stacks. Moreover, results indicated that the gross volume estimations of higher quality log stacks were closer for the three analyzed methods compared to estimations of poor-quality log stacks.left right left right left right

As a land use management system, agroforestry has environmental, economic and societal benefits over conventional agriculture or forestry. Important benefits of combining tree growth with agricultural crops and/or forage production systems include higher biodiversity through more diverse habitats, the control of runoff and soil erosion, the augmentation of soil water availability, the creation of microclimates, carbon sequestration and provision of a more diverse farm economy. As the climate changes, north eastern Germany is likely to be particularly prone to severe effects from droughts and wind erosion in the future. However, the area of land under agroforestry makes up less than 2% of the total agricultural area in Germany. Through qualitative interviews with key actors, this study analyzed the benefits of, potentials for and barriers to implementing agroforestry systems in the federal state of Brandenburg. Results showed that agroforestry systems have significant potential in relation to several benefits, particularly the mitigation of soil erosion and stabilization of microclimate regimes. Additionally, agroforestry has the potential to provide wood for energy production or material uses. Although a small but highly innovative and interlinked community exists, administrative barriers and high start-up costs currently hamper the transition from conventional agriculture to agroforestry systems.

The influence that parameters crookedness and taper have on the stack volume was analyzed by using a 3D-simulation model in this study. To do so, log length, diameters at the midpoint and both ends, crookedness, bark thickness, taper and ovality were measured in 1000 logs of Scots pine. From this database, several data sets with different proportions of crooked and tapered logs in stack as well as with different degrees of taper and crookedness were created and taken as basis to simulate the stacks and carry out the analysis. The results show how the variation of these parameters influences the stack volume and provide their volume variation grades. These rates of variation were compared with measurement guidelines of some countries and previous research works. In conclusion, the parameters crookedness and taper influence the stack volume to a considerable extent. Specifically, the stack volume is increased as the crookedness degree or the proportion of crooked logs increases. In contrast, the stack volume is reduced as the taper degree or the proportion of tapered logs increases. Furthermore, the results demonstrate the capability of this simulation model to provide accurate results which can serve as a basis for future studies.

The accurate estimation of timber volume is of the utmost importance. For industrial timber, the volume is often estimated as stacked cubic meters. In addition to manual measurements, volume estimation is possible with photo-optical systems. Over 100 piles of industrial timber of broadleaved tree species were analyzed. In the study, a standard manual measurement method for the estimation of wood pile volumes was compared with a smartphone based photo-optical application for the determination of woodpile volume. Mean gross volume of the piles was approximately 56 m³ and mean width of piles was 9.43 m. A strong correlation was found between the manual measurements and the photo-optical measurement. However, volume estimation of large volume piles seems to perform better in comparison to piles with small volumes. Further research is needed to determine the effects of variables such as log quality or quality of pile on volume estimation accuracy.

In commercial transaction of stacked roundwood, the estimation of the stack net volume plays a key role. One generalized method to determine the net volume is using conversion factors that relate the gross and net volumes. In this literature review the developed methods to estimate the conversion factors as well as their influencing parameters were analyzed based on 153 references from America and Europe. According to the results, 48 different methods (including their variants) for estimating the conversion factors were developed. The newest methods enabled their accurate determination inexpensively, e.g., photo-optical methods or 3D simulation models. The analyzed references revealed that 30 parameters influence the conversion factors. Based on this comprehensive review, each stakeholder involved in the roundwood supply chain can know which method is used for estimating the conversion factors in the analyzed territories and which influencing parameters should be considered when purchasing roundwood in order to accurately assess the solid wood content in the stacks.