This paper presents a new frequency controller for variable speed wind turbines connected to the grid under power imbalance conditions. It is based on the fast power reserve emulation technique, having two different operation modes: overproduction and recovery mode. In the first mode, the active power provided by wind turbines is set over the mechanical power, reducing their rotational speed. This overproduction power is estimated according to the frequency excursion. In the second mode, the active power is established under the mechanical power to recover the initial rotational speed through a smooth trajectory. The power system considered for simulation purposes includes thermal, hydro-power and wind-power plants. The controller proposed has been evaluated under different mix-generation scenarios implemented in Matlab/Simulink. Extensive results and comparison to previous proposals are also included in the paper.
An alternative approach for combined frequency control in multi-area power systems with significant wind power plant integration is described and discussed in detail. Demand response is considered as a decentralized and distributed resource by incorporating innovative frequency-sensitive load controllers into certain thermostatically controlled loads. Wind power plants comprising variable speed wind turbines include an auxiliary frequency control loop contributing to increase total system inertia in a combined manner, which further improves the system frequency performance. Results for interconnected power systems show how the proposed control strategy substantially improves frequency stability and decreases peak frequency excursion (nadir) values. The total need for frequency regulation reserves is reduced as well. Moreover, the requirements to exchange power in multi-area scenarios are significantly decreased. Extensive simulations under power imbalance conditions for interconnected power systems are also presented in the paper.
Currently, wind power is the fastest-growing means of electricity generation in the world. To obtain the maximum efficiency from the wind energy conversion system, it is important that the control strategy design is carried out in the best possible way. In fact, besides regulating the frequency and output voltage of the electrical signal, these strategies should also extract energy from wind power at the maximum level of efficiency. With advances in micro-controllers and electronic components, the design and implementation of efficient controllers are steadily improving. This paper presents a maximum power point tracking controller scheme for a small wind energy conversion system with a variable speed permanent magnet synchronous generator. With the controller, the system extracts optimum possible power from the wind speed reaching the wind turbine and feeds it to the grid at constant voltage and frequency based on the AC–DC–AC conversion system. A MATLAB/SimPowerSystems environment was used to carry out the simulations of the system. Simulation results were analyzed under variable wind speed and load conditions, exhibiting the performance of the proposed controller. It was observed that the controllers can extract maximum power and regulate the voltage and frequency under such variable conditions. Extensive results are included in the paper.
Wind power plants depend greatly on weather conditions, thus being considered intermittent, uncertain and non-dispatchable. Due to the massive integration of this energy resource in the recent decades, it is important that transmission and distribution system operators are able to model their electrical behaviour in terms of steady-state power flow, transient dynamic stability, and short-circuit currents. Consequently, in 2015, the International Electrotechnical Commission published Standard IEC 61400-27-1, which includes generic models for wind power generation in order to estimate the electrical characteristics of wind turbines at the connection point. This paper presents, describes and details the models for wind turbine topologies Types 1 and 2 following IEC 61400-27-1 for electrical simulation purposes, including the values for the parameters for the different subsystems. A hardware-in-the-loop combined with a real-time simulator is also used to analyse the response of such wind turbine topologies under voltage dips. The evolution of active and reactive powers is discussed, together with the wind turbine rotor and generator rotational speeds.
The effect of pressure on the structural, vibrational, and optical properties of lead thiogallate, PbGa 2 S 4 , crystallizing under room conditions in the orthorhombic EuGa 2 S 4 -type structure (space group Fddd ), is investigated.
Las Tecnologías de la Información y la Comunicación (TIC) se han vuelto indispensables en el nuevo modelo educativo híbrido, donde se combina la enseñanza presencial con la enseñanza online. Profesores y estudiantes deben adaptarse y participar activamente en el proceso de aprendizaje para aprovechar el máximo estas tecnologías, las cuales permiten una mayor accesibilidad y flexibilidad en la educación, mejorando la personalización y la colaboración del aprendizaje . En concreto, en este trabajo expone diferentes experiencias en el uso de material multimedia interactivo para ayudar a los estudiantes de las asignaturas de “Teoría de Circuitos” y “Electromagnetic experiments and their theoretical foundations” de la Escuela Técnica Superior de Ingenieros Industriales de la Universitat Politècnica de València, los cuales tienen dificultades para comprender los conceptos básicos de las asignaturas, lo que se refleja en los malos resultados que obtienen en las evaluaciones. Con la implementación de estos nuevos recursos multimedia se pretende mejorar la motivación del alumno y facilitar el aprendizaje de cada concepto o método explicado en las asignaturas. Tras su implementación, se muestra que dichas actividades mejoran significativamente el rendimiento de los estudiantes, obteniendo resultados positivos tanto en utilidad como en facilidad de uso por parte de los estudiantes.