This work presents a simple and accurate method for the calculation of both the self-inductance and the mutual inductance between thin-film capacitors, placed in close proximity in electromagnetic interference filters. From physical considerations regarding the impact of both skin and proximity effects, we approximate the currents flowing inside the capacitors at high frequencies by strip currents. This hypothesis is supported by electromagnetic simulations and measurements in this paper. On the basis of this model, we use analytical expressions to calculate both the self-inductance and the mutual inductance as a function of purely geometrical parameters such as the size of the capacitors, their orientation and the distances between them. Because no previous impedance or network parameters measurements are required to estimate these inductances, this technique is suitable for virtual prototyping design. We have constructed and measured several test boards to check the accuracy of the method and to identify its scope and limits. Also, in this work we employ this technique to study the applicability to thin-film capacitors of a design strategy originally conceived to reduce the negative effects of the inductive parasitics of surface-mount capacitors. We demonstrate that this design strategy significantly improves the attenuation provided by filters with thin-film capacitors at high frequencies.
11 June 2019 in IEEE Transactions on Electromagnetic Compatibility
This work analyzes the effect of conducting bands placed close to a common mode choke on the attenuation provided by an electromagnetic interference filter where the common mode choke is mounted. The main aim was to determine whether the response of the common mode choke can be modified and to clearly identify and quantify the physical mechanism responsible for the changes found in the attenuation of the common mode choke and the electromagnetic interference filter. The impact of grounded and ungrounded conducting surfaces was studied for the two more typical configurations of common mode chokes: vertically and horizontally mounted. This study has allowed us to devise an optimum shield for a common mode choke that can significantly improve the attenuation to both common mode and differential mode noise of an electromagnetic interference filter at high frequencies, where parasitic effects usually undermine the performance of the filter. Key features of the technique described here are that it can be applied easily and that it does not result in an increase of the weight, volume, or cost of the filter.
DC-DC isolated converters allowing a bidirectional flow of energy between High-Voltage DC and Low-Voltage DC networks have been proposed to be integrated in future on board power distribution systems. These converters must meet the specially stringent efficiency and power density requirements that are typical of the aeronautic industry. This makes it specially challenging to determine which converter topology is best suited for each particular application. This work presents a thorough review of several topologies of bidirectional DC-DC power converters that are considered good candidates to meet certain important aeronautic requirements, as those related with high efficiency and high power density. We perform simulations on virtual prototypes, constructed by using detailed component models, and optimized following design criteria that are in accordance with those typically imposed by aeronautic requirements. This comparative analysis is aimed to clearly identify the advantages and drawbacks of each topology, and to relate them with the required voltage and power levels. As an outcome, we point out the topologies that, for the required power level at the chosen switching frequencies, yield higher efficiency in the whole range of required operation points and that are expected to allow more important weight reductions.
This work presents a technique to measure the attenuation of differential mode noise provided by common mode chokes. The proposed setup is a simpler alternative to the balanced setup commonly employed to that end, and its main advantage is that it avoids the use of auxiliary circuits (baluns). We make use of a modal analysis of a high-frequency circuit model of the common mode choke to identify the natural modes actually excited both in the standard balanced setup and in the simpler alternative setup proposed here. This analysis demonstrates that both setups are equivalent at low frequencies and makes it possible to identify the key differences between them at high frequencies. To analyze the scope and interest of the proposed measurement technique we have measured several commercial common mode chokes and we have thoroughly studied the sensitivity of the measurements taken with the proposed setup to electric and magnetic couplings. We have found that the proposed setup can be useful for quick assessment of the attenuation provided by a common mode choke for differential mode noise in a frequency range that encompasses the frequencies where most electromagnetic compatibility regulations impose limits to the conducted emissions of electronic equipment.
The increase in electric power demands and the project to develop a high voltage DC power distributions system in future aircrafts has created the need for a new generation of DC/DC power converters. The design of these systems has to take into account the stringent electromagnetic compatibility requirements typical of aeronautic applications, which combined with strict weight and volume restrictions make it often very difficult to comply with the emissions limits established in the applicable electromagnetic compatibility norms. In this context it is highly advisable to incorporate electromagnetic compatibility considerations from the beginning of the design process. In this work we perform a through comparison of two candidate topologies for 270VDC/28VDC and 540VDC/28VDC 3kW power converters in terms of emission of conducted noise. We compare two topologies with four switches in the high voltage side: a full bridge and a three level NPC converter. We show that a careful modeling of the parasitic effects that cause noise emissions allows for obtaining valuable preliminary conclusions in the simulation stage of the design process. Also, we take advantage of the circuit models developed to compare these converters in terms of output voltage spectrum distortion and efficiency. We have found some differences between the performance of the converters in function of the input voltage and the topology. In particular, we have found that the three level converter is slightly less efficient and does not provide significant improvement in terms of reduction of common mode noise. We explain this apparent paradox by close analysis of the effect of the parasitic elements that model capacitive couplings in the converter.
In this work, we analyze the impact of output filter design techniques aimed to reduce conducted emissions at the output of a DCDC power converter. A thorough analysis, based on high-frequency circuit models of the converter, is performed to assess expected improvements offered by different design strategies. This analysis is then confronted with measurements of conducted emissions at the output of a 300 W 48 V to 12 V Phase Shift Full Bridge (PSFB) prototype. Those experimental results demonstrate that a symmetric arrangement of the output LC filter and a direct bonding of the return output terminal of the converter to chassis are effective to reduce common mode conducted emissions at the output. Those results also demonstrate that the symmetry of the output LC filter can reduce conducted emissions in differential mode at high frequencies, where common mode to differential mode conversion is the predominant contribution to differential mode noise. However, direct bonding to chassis of the return output terminal may be ineffective at high frequencies due to the parasitic inductance associated with this connection. Main conclusions drawn for this analysis are applicable in general for isolated converters with a high voltage step between high and low voltage sides. Since the techniques of reduction of conducted emissions studied here do not increase the number of filter components, they are especially suitable for applications where high power density is an important requirement, e.g., aerospace or automotive applications.