DC-DC isolated converters allowing a bidirectional flow of energy between High-Voltage DC and Low-Voltage DC networks have been proposed to be integrated in future on board power distribution systems. These converters must meet the specially stringent efficiency and power density requirements that are typical of the aeronautic industry. This makes it specially challenging to determine which converter topology is best suited for each particular application. This work presents a thorough review of several topologies of bidirectional DC-DC power converters that are considered good candidates to meet certain important aeronautic requirements, as those related with high efficiency and high power density. We perform simulations on virtual prototypes, constructed by using detailed component models, and optimized following design criteria that are in accordance with those typically imposed by aeronautic requirements. This comparative analysis is aimed to clearly identify the advantages and drawbacks of each topology, and to relate them with the required voltage and power levels. As an outcome, we point out the topologies that, for the required power level at the chosen switching frequencies, yield higher efficiency in the whole range of required operation points and that are expected to allow more important weight reductions.
14 June 2023 in IEEE Transactions on Power Electronics
This article presents a method for characterization of common-mode chokes aimed at constructing accurate virtual prototypes of electromagnetic interference filters. This method is based on a general modal analysis that identifies the natural modes of a symmetric four-port network in a power line. Natural modes excited in the setups defined in the CISPR-17 norm to characterize filtering devices are determined. From this analysis, two simple measurement setups particularly suitable for characterizing common-mode chokes are identified, and a decision-making algorithm is presented to determine the parameters of a configurable circuit model of the common-mode choke. This circuit model is especially devised so that each one of its different circuit blocks can be associated with a single modal response of the common-mode choke. This, along with the use of physical criteria to define the basic schematic of each circuit block, ensures the simplicity, accuracy, and generality of the final circuit model. Characterization of many commercial common-mode chokes with different core materials and winding configurations has been carried out to demonstrate that this circuit model is able to accurately account for the actual response of different types of common-mode chokes in a wide frequency range.
14 May 2024 in IEEE Transactions on Electromagnetic Compatibility
Parasitic capacitances typically undermine the filtering performance of common mode chokes at high frequencies. This work demonstrates that these parasitic capacitances can be reduced by using a wise winding strategy that depends on the physical properties of the core material. Due to its practical interest, we specifically focus on single-layer common mode chokes wounded on NiZn or MnZn ferrite cores. Based on a physical model that enables the identification of parameters influencing the electrical coupling between the turns of the coils of the choke, the hypothesis proposed is that the optimal winding configuration depends on the core material, differing for NiZn and MnZn cores. To verify this hypothesis and to assess improvements actually achieved by optimum winding strategies, an accurate high-frequency model of the common mode choke along with an efficient characterization technique are used to numerically estimate the parasitics of common-mode chokes with different core materials and winding configurations. In addition, the filtering performance of these common mode chokes have been measured and compared.
26 January 2024 in IEEE Transactions on Power Electronics
Common mode chokes are widely employed to reduce common mode emissions of three phase systems. This work presents an advanced technique for analyzing and characterizing common mode chokes with three or four windings. The central idea of the method is a modal analysis of the choke, where the modes are based on the modes of the noise signal transmitted by the three-phase line. These modes are defined following the criterion of its suitability from the perspective of electromagnetic interference control. This modal analysis is used to propose a circuit model of the choke that accounts for the impact of high-frequency parasitic effects and, at the same time, allows for a straight forward parameter identification. This parameter identification is achieved by using a characterization technique that makes use of measurements of the response of the common mode choke in simple connections, whose suitability is justified thanks to the ability of the modal analysis to provide analytical and easy-to-interpret expressions of these connections. This makes also possible to predict and quantify mode conversions caused by the device in the three-phases line. The accuracy of the obtained circuit model within a wide frequency range has been demonstrated by comparing measurements with calculated responses for several three- and four-wires common mode chokes.