Tomasz Wojdat

Dr. Tomasz Wojdat

Wroclaw University of Science and Technology, Faculty of Mechanical Engineering, Department of Metal Forming, Welding and Metrology
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2016 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Closed access
TWTomasz Wojdat
Tomasz Wojdat
Marcin WinnickiMarcin Winnicki
Marcin Winnicki
Małgorzata RutkowskaMałgorzata Rutkowska
Małgorzata Rutkowska
SKSzymon Krupiński
Szymon Krupiński
KKKrzysztof Kubica
Krzysztof Kubica

5 October 2018 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
TWTomasz Wojdat
Tomasz Wojdat
Marcin WinnickiMarcin Winnicki
Marcin Winnicki
SŁS. Łamasz
S. Łamasz
AŻA. Żuk
A. Żuk

7 December 2024 in Materials
Verified
Journal Article
Open access
PDF file
TWTomasz Wojdat
Tomasz Wojdat
TPTomasz Piwowarczyk
Tomasz Piwowarczyk
This article presents research on advanced surface preparation methods for sintered carbides (WC-Co, grade B2) commonly used in the tool industry, particularly in the context of bonding these materials with C45 steel using adhesives. Sintered carbides are widely used due to their high hardness, wear resistance, and good ductility, making them ideal for manufacturing tools operating in harsh conditions. Traditional bonding methods, such as brazing and welding, often result in stresses and cracks. Adhesive bonding has therefore emerged as an effective alternative to mitigate these challenges. The research focuses on comparing the results obtained through modern surface treatment techniques, such as laser micro-texturing and plasma treatment, with traditional methods like grinding, abrasive blasting, and electrolytic etching. The influence of these methods on adhesion properties and the strength of adhesive bonds was evaluated through mechanical tests, including static shear and pull-off tests. An approximately 50% increase in the mechanical strength of adhesive joints was observed for surfaces treated with low-temperature plasma (operating voltage: 18 kV, flow of gasses: 20 l/min., treatment time: 60 s) and laser micro-texturing (infrared fiber laser, wavelength: 1064 nm (±5 nm), power: 20 W), as compared to mechanical grinding. The shear strength of the adhesive joints was equal to 32 MPa and 30 MPa on average in the case of treatment with low-temperature plasma made of helium and argon, respectively. The highest strength of an adhesive joint was equal to 34.5 MPa on average in the case of laser micro-texturing.

4 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
TWTomasz Wojdat
Tomasz Wojdat
PKPAWEŁ KUSTROŃ
PAWEŁ KUSTROŃ
KJKarol Jaśkiewicz
Karol Jaśkiewicz
JPJarosław Pabian
Jarosław Pabian
The purpose of the work was to test the welded joints of aluminum alloys EN AW-7075 and EN AW-6082, which are used to join individual structural elements of car bodies, e.g., B-pillar with the body. The joints were made using the low-energy cold metal transfer (CMT) arc welding method. The results of the structure investigations of lap and butt joints, as well as tests of mechanical properties are presented. The influence of linear energy and the way of arranging materials in lap joints on the possibility of hot cracks occurrence has been demonstrated. The shear strength of lap joints was equal to 150 MPa, while the tensile strength of butt joints was equal to 375 MPa. The highest hardness reduction was observed in the heat affected zone (HAZ) from the EN AW-7075 alloy side in the range of 98 to 138 HV 0.05. In addition, a significant reduction of the corrosion resistance in the transition zone between HAZ and the base material (EN AW-7075 alloy) in the medium salinity environment, corresponding to the sea conditions according to ASTM G85 was indicated.

30 May 2020 in Welding Technology Review
Verified
Journal Article
Open access
ZMZbigniew Mirski
Zbigniew Mirski
JPJarosław Pabian
Jarosław Pabian
TWTomasz Wojdat
Tomasz Wojdat
JHJan Hejna
Jan Hejna
The paper presents the influence of the brazing gap width on the structure of bonded joints during the production of aluminum heat exchangers, using brazing technology, in tunnel furnaces with controlled atmosphere. Based on the wedge test, an analysis and qualitative assessment of brazed joints was made for the changing width of the brazing gap and the filler metal used. For the received brazed joints, metallographic tests were carried out using light and electron microscopy (SEM) and microhardness measurements in the characteristic areas of brazed joints. Based on the results obtained, the recommended width of the brazing gap was determined.

12 December 2019 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
TWTomasz Wojdat
Tomasz Wojdat
PKP. Kustroń
P. Kustroń
KJK. Jaśkiewicz
K. Jaśkiewicz
MZM. Zwierzchowski
M. Zwierzchowski
AMA. Margielewska
A. Margielewska
In the paper, verification of welding process parameters of overlap joints of aluminium alloys EN AW-6082 and EN AW-7075, determined on the grounds of a numerical FEM model and a mathematical model, is presented. A model was prepared in order to determine the range of process parameters, for that the risk of hot crack occurrence during welding the material with limited weldability (EN AW-7075) would be minimum and the joints will meet the quality criteria. Results of metallographic and mechanical examinations of overlap welded joints are presented. Indicated are different destruction mechanisms of overlap and butt joints, as well as significant differences in their tensile strength: 110 to 135 MPa for overlap joints and 258 MPa on average for butt joints.