The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i) microhardness measurements, (ii) tensile tests, (iii) bending tests, and (iv) shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i) changing the geometry of bonding surface, (ii) using the interlayer, or (iii) heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.
The article presents the results of the development works and research on the atomization process carried out using two prototype high-power ultrasonic systems. Ultrasonic systems have been designed to develop a new metal powder production process; these materials are increasingly used in modern manufacturing processes such as additive technologies or spraying and surfacing processes. The preliminary studies presented in the article were conducted for water to assess the effectiveness of both systems and to verify the theoretical and structural assumptions. In ultrasonic atomization, the ultrasonic wave causes the phenomenon of cavitation, which leads to the overcoming of the surface tension forces of the liquid and its disintegration into fine droplets. The important parameters that affect the properties of the produced droplets include, among others, the frequency of the sonotrode vibrations and the amplitude of the vibrations of the working plate. As part of the research, the paper presents the process of selecting the sonotrode geometry for two different values of the transducer’s natural frequencies (20 kHz and 70 kHz). In the design process, the finite element method was used to perform a harmonic analysis and develop the geometry of the sonotrode and the working plate. The design assumptions and the design process were presented. The modeled and then ultrasonic waveguides were verified experimentally by measuring the deflection distribution on the working plate surface using a high-precision laser displacement sensor. Then, the work ultimately resulted in conducting atomization tests of water. The obtained aerosols and the mechanism of their formation were studied using a high-speed camera. Finally, using Matlab R2020a software and image analysis scripts, it was possible to analyze the droplet size distribution generated by both systems. It was observed that 50% of the produced droplets were in the range of 35–55 μm for a 20 kHz system, while for a 70 kHz system it was 10–25 μm, which is a very satisfying distribution in terms of metal powder atomization.
Metal–plastic composites (MPCs) are gaining importance mainly due to high strength to weight ratio. They consist of three layers, two outer metallic cover sheets, and a plastic core. The presence of that inner plastic layer makes them rather unsuitable for joining by means of any conventional welding processes, which significantly reduces the application range of MPC. In this work, three various resistance spot welding (RSW)-based concepts were developed to overcome that limitation and join Litecor to DP600 steel. In all cases, a dedicated initial stage was implemented to RSW, which was aimed at removing the non-conductive polymer layer from the welding zone and creating the proper electrical contact for the resistance welding. These were, namely: (i) shunt current-assisted RSW; (ii) induction heating-assisted RSW; and (iii) ultrasonic-assisted RSW. The development of each concept was supported by finite element modeling, which was focused on setting the proper process parameters for polymer layer removal. Finally, the macro- and microstructure of exemplary RSW joints are shown and the most common spot weld features as well as the further development possibilities are discussed.
1 February 2018 in Archives of Civil and Mechanical Engineering
One of the main limitations in application of nanostructured carbide-free bainite as a construction material is the difficulty of joining. This research presents a structural characterization of welded joints of medium carbon 55Si7 grade steel after the welding process with a regeneration technique as well as post welding heat treatment (PWHT). The hardness distribution of the welded joint with regeneration exhibit an overall decrease in hardness when compared to the base material and a significant decrease in hardness was observed in the heat-affected zone (HAZ). Unfavorable hardness distribution was caused by the presence of diffusion-type transformations products (pearlite) in the HAZ and bainite degradation processes. On the other hand, welding with the PWHT promotes the achievement of a comparable level of hardness and structure as in the base material. However, a slight decrease in hardness was observed in the weld zone due to the micro-segregation of the chemical composition caused by the indissoluble solidification structure. Based on the structural analysis, it was found that steel with relatively low hardenability (55Si7) should be welded using PWHT rather than a regeneration technique.
25 May 2020 in Journal of Nondestructive Evaluation
The article demonstrates an effective solution for ultrasonic quality monitoring of transmission and drive components of motor vehicles, joined using an innovative method called magnetically impelled arc butt welding (MIAB). The major challenge was the application of ultrasonic technology for quick and reliable testing of thin-walled components with complex geometry. To solve this problem the idea of using ultrasonic subsurface waves was investigated. By using finite elements method (FEM) the angle of the ultrasonic beam incident on the tested element and the frequency of the ultrasonic transducer were verified. Then, scanning acoustic microscopy (SAM) and X-ray computed tomography (CT), both nondestructive tests on thin-walled welded tubular components were performed. The research have shown that it is possible to detect defects with diameter of 0.3 mm with the angle of incidence of wave 31.5°. The results of the numerical analysis were compared with the experimental approach and confirmed the usefulness of proposed method. Finally, the potential of using immersion ultrasonic technique for quick and reliable validation of thin-walled tubular components was proven, as the test duration for a one elements was around 3 s.