This paper proposes topological enhancements to increase voltage gain of ultra-low-voltage (ULV) inverter-based OTAs. The two proposed improvements rely on adoption of composite transistors and forward-body-biasing. The impact of the proposed techniques on performance figures is demonstrated through simulations of two OTAs. The first OTA achieves a 39 dB voltage gain, with a power consumption of 600 pW and an active area of 447 μm2. The latter allies the forward-body-bias approach with the benefit of the independently biased composite transistors. By combining both solutions, voltage gain is raised to 51 dB, consuming less power (500 pW) at the cost of an increased area of 727 μm2. The validation has been performed through post-layout simulations with the Cadence Analog Design Environment and the TSMC 180 nm design kit, with the supply voltage ranging from 0.3 V to 0.6 V.
This paper deals with a single-stage single-ended inverter-based Operational Transconductance Amplifiers (OTA) with improved composite transistors for ultra-low-voltage supplies, while maintaining a small-area, high power-efficiency and low output signal distortion. The improved composite transistor is a combination of the conventional composite transistor and forward-body-biasing to further increase voltage gain. The impact of the proposed technique on performance is demonstrated through post-layout simulations referring to the TSMC 180 nm technology process. The proposed OTA achieves 54 dB differential voltage gain, 210 Hz gain–bandwidth product for a 10 pF capacitive load, with a power consumption of 273 pW with a 0.3 V power supply, and occupies an area of 1026 μm2. For a 0.6 V voltage supply, the proposed OTA improves its voltage gain to 73 dB, and achieves a 15 kHz gain–bandwidth product with a power consumption of 41 nW.
23 March 2020 in Analog Integrated Circuits and Signal Processing
In this paper, a new technique for improvement on the DC voltage gain, while keeping the high-linearity in symmetrical operational transconductance amplifier (OTA) bulk-driven (BD) topology is proposed. These features are achieved by allying two topological solutions: enhanced forward-body-biasing self-cascode current mirror, and source degeneration. The proposed concept is demonstrated through simulations with typical process parameters and Monte Carlo analysis on nominal transistors of the CMOS TSMC 180 nm node. Results indicate that the proposed OTA can achieve a very small transconductance, only 542 pA/V while keeping a voltage gain higher than 60 dB, 150 dB CMRR, and high linearity of 475 mVpp (1% THD), consuming only 1.9 nW for a supply voltage of 0.6 V. This set of features allows the proposed OTA to be an attractive solution for implementing OTA-C filters for the analog front-ends in wearable devices and bio-sensing.
Inverter-based Operational Transconductance Amplifiers (OTAs) are versatile and friendly scalable analog circuit blocks. Especially for the new CMOS technological nodes, several recent applications have been extensively using them, ranging from Analog Front End (AFE) to analog-to-digital converters (ADC). This work tracks down the current advances in inverter-based OTAs design, comparing their basic fully differential structures, such as Nauta (N), Barthelemy (B), Vieru (V) and Mafredini (M) ones, and, in addition, mixing them up to propose new fully differential single-ended and two-stage hybrid versions. The new herein-proposed fully differential hybrid OTAs are the composition of Barthelemy/Nauta (B/N), Barthelemy/Manfredini (B/M), Nauta/Vieru (N/V), and Manfredini/Vieru (M/V) OTAs. All OTAs were designed using the same Global Foundries 180 nm open-source PDK and their performances are compared for post-layout simulations.
This work presents a self biased current reference circuit based on the MOSFET Zero Temperature Coefficient (ZTC) condition. To achieve lower supply voltage ( $V_{\text{DD}}$ ) operation, the proposed circuit employs forward body biasing technique to decrease the MOSFET ZTC biasing point. In addition, a body-driven pseudo differential Operational Transconductance Amplifier (OTA) is used to further reduce the minimum supply voltage. From transitor-level simulations, the current reference is predicted to have an Effective Temperature Coefficient ( $TC_{\text{eff}}$ ) of 65 ppm/°C from −55 to 125 °C and a fabrication sensitivity of $\sigma/\mu = 6.5\ \%$ , including process and mismatch variability. The power supply sensitivity is around 0.75% /V for this new reference.