Orazio Aiello

Prof. Dr. Orazio Aiello

Department of Naval, Electrical, Electronic, and Telecommunications Engineering (DITEN), University of Genoa, Genoa, Liguria, Italy
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 June 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
Pedro Filipe Leite Correia de ToledoPedro Filipe Leite Correia de Toledo
Pedro Filipe Leite Correia de Toledo
Paolo Stefano CrovettiPaolo Stefano Crovetti
Paolo Stefano Crovetti
Orazio AielloOrazio Aiello
Orazio Aiello
MAMassimo Alioto
Massimo Alioto
In this paper, passive-less fully-digital operational transconductance amplifiers (DIGOTA) for energy- and area-constrained systems are modeled and analyzed from a design viewpoint. The digital behavior of DIGOTAs is modeled as an equivalent small-signal differential-mode circuit with zero bias current, and a common-mode feedback loop operating as a self-oscillating threshold sampler. Such continuous-time equivalent circuits are used to derive an explicit model of the main performance parameters that are generally adopted to characterize OTAs. This provides an insight into circuit operation and allows to derive practical guidelines to achieve a given design target. Among the others, an explicit model is derived for the DC gain, the frequency response, the gain-bandwidth product, the input-referred noise, and the input offset voltage. The models are validated via direct comparison with multi-die measurement results in CMOS 180 nm. From an application viewpoint, the voltage (power) reduction down to 0.25 V (sub-nW) uniquely enable direct harvesting (e.g., with solar cells), suppressing any intermediate DC-DC conversion stage. This further enhances the area efficiency advantage of DIGOTA stemming from its fully-digital nature, making it well suited for cost-sensitive and purely-harvested systems.

29 September 2020 in IEEE Solid-State Circuits Letters
Verified
Journal Article
Closed access
Pedro Filipe Leite Correia de ToledoPedro Filipe Leite Correia de Toledo
Pedro Filipe Leite Correia de Toledo
Paolo Stefano CrovettiPaolo Stefano Crovetti
Paolo Stefano Crovetti
Orazio AielloOrazio Aiello
Orazio Aiello
MAMassimo Alioto
Massimo Alioto
A fully-digital operational transconductance amplifier (DIGOTA) architecture for tightly energy-constrained low-cost systems is presented. A 180nm DIGOTA testchip exhibits an area below the 1,000-μm2 wall, and 2.4-nW power under 150pF load, and a minimum supply voltage Vmin of 0.25 V. In the 0.3-0.5 V supply range, DIGOTA improves the areanormalized small (large) signal energy FoM by at least 836X (267X) over prior sub-500mV OTAs, while reducing area by 27-85X. The low-Vmin and nW-power features are shown to enable direct harvesting at the mm scale.

17 January 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
Orazio AielloOrazio Aiello
Orazio Aiello
Paolo Stefano CrovettiPaolo Stefano Crovetti
Paolo Stefano Crovetti
LLLongyang Lin
Longyang Lin
MAMassimo Alioto
Massimo Alioto
In this paper, a pW-power relaxation oscillator for sensor node applications is presented. The proposed oscillator operates over a wide supply voltage range from nominal down to deep sub-threshold and requires only a sub-pF capacitor for Hz-range output frequency. A true pW-power operation is enabled thanks to the adoption of an architecture leveraging transistor operation in super-cutoff, the elimination of voltage regulation, and current reference. Indeed, the oscillator can be powered directly from highly variable voltage sources (e.g., harvesters and batteries over their whole charge/discharge cycle). This is achieved thanks to the wide supply voltage range, the low voltage sensitivity of the output frequency and the current drawn from the supply. A test chip of the proposed oscillator in 180 nm exhibits a nominal frequency of approximately 4 Hz, a supply voltage range from 1.8 V down to 0.3 V with 10%/V supply sensitivity, 8-18-pA current absorption, and 4%/°C thermal drift from -20 °C to 40 °C at an area of 1600 μm 2 . To the best of the authors' knowledge, the proposed oscillator is the only one able to operate from sub-threshold to nominal voltage.

9 April 2020 in IEEE Access
Verified
Journal Article
Open access
Orazio AielloOrazio Aiello
Orazio Aiello
Paolo Stefano CrovettiPaolo Stefano Crovetti
Paolo Stefano Crovetti
MAMassimo Alioto
Massimo Alioto
In this paper, fully-synthesizable Successive Approximation Register (SAR) Analog-to-Digital Converters (ADCs) suitable for low-cost integrated systems are proposed both for voltage and current input. The proposed ADCs are digital in nature and are based on the Dyadic Digital Pulse Modulation (DDPM) Digital-to-Analog (DAC), instead of a traditional capacitive DAC. The proposed fully-digital ADC architectures enable low-effort design, silicon area reduction, and voltage scaling down to the near-threshold region. Compared to traditional analog-intensive designs, their digital nature allows easy technology and design porting, digital-like area shrinking across CMOS technology generations, and also drastically reduced system integration effort through immersed-in-logic ADC design. The voltage-input ADC architecture is demonstrated with a 40-nm testchip showing 3,000-μm2 area, 6.4-bit ENOB, 2.8kS/s sampling rate, 40.4dB SNDR, 49.7dB SFDR, and 3.1μW power at 1V. A current-input ADC is also demonstrated for direct current readout without requiring a trans-resistance stage. 40-nm testchip measurements show a 5-nA to 1-μA input range, 4,970μm2 area, 6.7-bit ENOB and 2.2-kS/s sample rate, at 0.94-μW power. Compared to the state of the art, the proposed ADC architecture exhibits the highest level of design automation (standard cell), lowest area, and the unique ability to cover direct acquisition of both voltage and current inputs, suppressing the need for transresistance amplifier in current readout.

1 September 2020 in Electronics
Verified
Journal Article
Open access
PDF file
LRLuis Henrique Rodovalho
Luis Henrique Rodovalho
Orazio AielloOrazio Aiello
Orazio Aiello
CRCesar Rodrigues
Cesar Rodrigues
This paper proposes topological enhancements to increase voltage gain of ultra-low-voltage (ULV) inverter-based OTAs. The two proposed improvements rely on adoption of composite transistors and forward-body-biasing. The impact of the proposed techniques on performance figures is demonstrated through simulations of two OTAs. The first OTA achieves a 39 dB voltage gain, with a power consumption of 600 pW and an active area of 447 μm2. The latter allies the forward-body-bias approach with the benefit of the independently biased composite transistors. By combining both solutions, voltage gain is raised to 51 dB, consuming less power (500 pW) at the cost of an increased area of 727 μm2. The validation has been performed through post-layout simulations with the Cadence Analog Design Environment and the TSMC 180 nm design kit, with the supply voltage ranging from 0.3 V to 0.6 V.

12 February 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
Orazio AielloOrazio Aiello
Orazio Aiello
Paolo Stefano CrovettiPaolo Stefano Crovetti
Paolo Stefano Crovetti
Pedro Filipe Leite Correia de ToledoPedro Filipe Leite Correia de Toledo
Pedro Filipe Leite Correia de Toledo
MAMassimo Alioto
Massimo Alioto
An ultra-low voltage, ultra-low power rail-to-rail dynamic voltage comparator solely based on digital standard cells is presented. Thanks to its digital nature, the comparator can be designed and integrated with fully-automated digital design flows and can operate at very low voltages down to deep sub-threshold. Measurements on an 180nm testchip show correct operation under rail-to-rail common-mode input at a supply voltage ranging from 0.6V down to 0.15V. The comparator delay (power) is lower than 442μs (10pW) at 0.15-V supply voltage. The input offset voltage is less than 30mV over the entire rail-to-rail common-mode input and supply range. The minimum supply voltage and power are the lowest reported to date, and make the circuit suitable for direct powering from mm-scale harvesters.