Flexible substrates have become essential in order to provide increased flexibility in wearable sensors, including polymers, plastic, paper, textiles and fabrics. This study is to comprehensively summarize the bending capabilities of flexible polymer substrate for general Internet of Things (IoTs) applications. The basic premise is to investigate the flexibility and bending ability of polymer materials as well as their tendency to withstand deformation. We start by providing a chronological order of flexible materials which have been used during the last few decades. In the future, the IoT is expected to support a diverse set of technologies to enable new applications through wireless connectivity. For wearable IoTs, flexibility and bending capabilities of materials are required. This paper provides an overview of some abundantly used polymer substrates and compares their physical, electrical and mechanical properties. It also studies the bending effects on the radiation performance of antenna designs that use polymer substrates. Moreover, we explore a selection of flexible materials for flexible antennas in IoT applications, namely Polyimides (PI), Polyethylene Terephthalate (PET), Polydimethylsiloxane (PDMS), Polytetrafluoroethylene (PTFE), Rogers RT/Duroid and Liquid Crystal Polymer (LCP). The study includes a complete analysis of bending and folding effects on the radiation characteristics such as S-parameters, resonant frequency deviation and the impedance mismatch with feedline of the flexible polymer substrate microstrip antennas. These flexible polymer substrates are useful for future wearable devices and general IoT applications.

CubeSats are a class of miniaturized satellites that have become increasingly popular in academia and among hobbyists due to their short development time and low fabrication cost. Their compact size, lightweight characteristics, and ability to form a swarm enables them to communicate directly with one another to inspire new ideas on space exploration, space-based measurements, and implementation of the latest technology. CubeSat missions require specific antenna designs in order to achieve optimal performance and ensure mission success. Over the past two decades, a plethora of antenna designs have been proposed and implemented on CubeSat missions. Several challenges arise when designing CubeSat antennas such as gain, polarization, frequency selection, pointing accuracy, coverage, and deployment mechanisms. While these challenges are strongly related to the restrictions posed by the CubeSat standards, recently, researchers have turned their attention from the reliable and proven whip antenna to more sophisticated antenna designs such as antenna arrays to allow for higher gain and reconfigurable and steerable radiation patterns. This paper provides a comprehensive survey of the antennas used in 120 CubeSat missions from 2003 to 2022 as well as a collection of single-element antennas and antenna arrays that have been proposed in the literature. In addition, we propose a pictorial representation of how to select an antenna for different types of CubeSat missions. To this end, this paper aims is to serve both as an introductory guide on CubeSats antennas for CubeSat enthusiasts and a state of the art for CubeSat designers in this ever-growing field.

Application demand for faster data rates is driving the need for wider operating bandwidth of future 5G/6G communication systems which in turn poses stringent requirements on the design of suitable antennas. A candidate antenna that can support 5G/6G systems are reflectarrays (RAs) due to their numerous potentials, such as high gain, beam shaping, beam scanning, reconfigurability and multi-beam characteristics. However, reflectarrays are usually limited by their narrowband characteristics. Hence, this work examines the state of the art of wideband reflectarrays. Wideband reflectarrays are reviewed and categorized according to four wideband phase tuning mechanisms. The bandwidth is reviewed and compared both from a unit cell and reflectarray system perspective with emphasis on the gain-bandwidth performance. Different wideband unit cell geometries are covered and grouped by the wideband phase tuning approach. The effect of each wideband phase tuning approach on the gain-bandwidth RA performance is then analyzed by considering the operating frequency, the reflection phase range, the substrate structure and material, the aperture size, the aperture efficiency, the focal distance, the cross-polarization performance as well as the gain and side lobe levels. Finally, the phase tuning approaches are compared against each other, and guidelines are provided for designing reflectarrays with wide gain-bandwidth.

CubeSats have revolutionized the way scientists and students perceive space. The majority of CubeSat communication is greatly limited by the AX.25 standards, the small communication window, the available transmission power, and the available bandwidth at VHF/UHF band. As a result, CubeSat radios could only establish low data rate links which restrict the communication capabilities of a CubeSat mission. In this paper, a brief review of current Software Defined Radios used in space missions is given. In addition, two different design methodologies for Software Defined Radios for CubeSats are proposed that can be used as guideline for CubeSat developers. Finally, a High Data Rate Software Defined Radio for the UOW CubeSat project is presented that address all the above limitations. The radio operates at S-band, employs Quadrature Amplitude Modulation with a maximum data rate of 60Mbps consuming 2.6 Watts in transmit mode and 0.4 Watts in receive mode. The digital signal processing functions and the mode control of the radio are orchestrated by a Field Programmable Gate Array System-on Chip. The analog Radio Frequency domain is accommodated by a 4-layer Printed Circuit Board with dimensions of 92mm x 88mm. The goal of the UOW CubeSat radio is an adaptive, on-flight reconfigurable communication platform that will revolutionize the current communication capabilities of the CubeSats and expand nanosatellites mission perspectives.

Flexible wearable wireless devices have found practical uses as their cost has fallen and Internet of Things applications have gained further acceptance. These devices are gaining further use and acceptance in the consumer and wearable space for applications such as logistical tracking and maintaining sensor information, including temperature, humidity, and location. In such applications, antennas are exposed to bending and crumbling. Therefore, flexible substrate antennas for use with polymer-based flexible devices are an important area of research that needs to be addressed. In this study, the bending capabilities of flexible polymer substrate antennas for general IoT applications were practically analyzed by fabricating flexible antennas on Polyethylene Terephthalate (PET), Polytetrafluoroethylene (PTFE) Teflon, and Polyvinylchloride (PVC) substrates operating at 2.45, 4.45, and 7.25 GHz frequencies. The basic premise was to investigate the flexibility and bending ability of polymer materials, and their tendency to withstand deformation. In the current paper, we start by providing an equivalent model for the flexible microstrip patch antenna under bent conditions, followed by outlining the process of designing flexible antennas on polymer substrates. Finally, the fabricated flexible antennas were tested in an anechoic chamber for various radiation characteristics such as reflection coefficients, operating frequency shifts, and impedance mismatch with the transmission line, under bending conditions up to 7 mm. The practical outcomes were then compared with our recent investigation on flexible polymer substrate antennas for wearable applications. This study provides a means to select a suitable polymer substrate for future wearable sensors and antennas with high bendability.

This article presents a compact wideband high gain patch antenna for CubeSat. The proposed metal-only antenna mainly consists of an upper patch, a folded ramp-shaped patch and shoring pins connecting the antenna with the ground plane. By adjusting the lengths and widths of two arms of the upper F-shaped patch, a second resonant frequency is generated, and hence, the −10 dB bandwidth is increased. Moreover, the effect of arms’ lengths and widths on reflection coefficients, operating frequency and bandwidth is presented. To validate the design and the simulation results, a prototype metal-only patch antenna was fabricated and tested in a Chamber. A good agreement between the simulated and measured results is achieved. The measured results show that the fabricated prototype achieves a −10 dB bandwidth of 44.9% (1.6–2.7 GHz), a small reflection coefficient of −24.4 dB and a high efficiency, i.e., 85% at 2.45 GHz. The radiation performance of the proposed antenna is measured, showing a peak realized gain of 8.5 dBi with cross polarization level less than −20 dB at 2.45 GHz and a 3 dB gain bandwidth of 61.22%.